Viking Quiet Cool VCRB5301 Service Manual Download Page 2

Page: 2 / 47

Table of Contents

Important Information ..................................................... 3

Safety Information .................................................... 3

Warnings .................................................................. 4

Electrical Requirements ........................................... 4

Tip Over Hazard ....................................................... 4

General Information ........................................................ 5

Model – Serial Number Matrix ................................ 5

Model Numbers ................................................... 5

Serial Numbers .................................................... 5

Operation ........................................................................ 6

Settings and Functions ............................................ 6

Electronic Temperature Settings .............................. 6

Key Press Confirmation

........................................... 6

Fast Cool .................................................................. 7

MAX REF ................................................................. 7

Forced Pull-Down (Forced compressor start) .......... 8

Forced Defrost ......................................................... 8

Showroom Mode ..................................................... 8

Sabbath Mode .......................................................... 9

Fahrenheit to Celsius ............................................... 9

Display Panel Operation ........................................ 10

Temperature Control Operation .............................11

Door Hinge Adjustment .......................................... 12

Height Adjustment .................................................. 13

Disassembly ................................................................. 14

Parts Location–Control Panel ................................ 14

Upper Grille Assembly ........................................ 15

Control Panel ..................................................... 15

Control Panel (continued) .................................. 16

Overlay Switch .................................................... 16

Overlay Switch (continued) ................................. 17

High Voltage Board ............................................ 17

Low Voltage Board ............................................. 17

Power Disconnect Switch ................................... 18

Inverter ................................................................ 18

Inverter (continued) ............................................ 19

Condenser Fan ................................................... 19

Parts Location – Refrigerator Compartment .......... 20

Light Assembly .................................................... 21

Upper Fresh Food Fan ....................................... 21

Interior Lights ...................................................... 21

Fresh Food Thermistor ....................................... 22

Lower Fan Assembly .......................................... 22

Float Switch ........................................................ 23

Drain Pan Heater ................................................ 23

Service Procedures ...................................................... 24

Program Modes ..................................................... 24

Program Mode A .................................................... 24

Display REF Temperature ................................... 24

Defrost mode selection ....................................... 24

Conventional defrost time adjustment (CRTD) ... 24

Compressor low speed frequency ...................... 25

Adjust Cut-In Hysteresis .................................... 25

Adjust Cut-Out Hysteresis .................................. 26

Display Software Version .................................... 26

Exiting Mode A .................................................... 27

Program Mode B .................................................... 27

Adjust Refrigerator Temperature Offset .............. 27

Adjust MAX REF duration ................................... 28

Adjust FAST COOL duration ............................... 28

Adjust Door Open Alarm delay ........................... 28

Adjust Compressor Dwell Time ........................... 28

Adjust FAST COOL duration ............................... 28

Adjust Door Open Alarm delay ........................... 29

Adjust Compressor Dwell Time ........................... 29

Adjust Compressor High Frequency ................... 29

Adjust DC Fan Cycling On Time ......................... 29

Adjust DC Fan Cycling Off Time ......................... 29

Exiting Mode B .................................................... 30

Program Mode C .................................................... 30

Set Model type .................................................... 30

Adjust Refrigerator Upper Temperature Limit ..... 31

Adjust Refrigerator Lower Temperature Limit ..... 31

Defrost lockout adder .......................................... 31

Defrost start delay ............................................... 31

Defrost termination delay .................................... 31

Constant Evaporator fan mode ........................... 32

Plant mode .......................................................... 32

ALARMS ................................................................ 33

1. High Temp Alarm ............................................ 33

2. Open Thermistor Alarm ................................... 33

3. Shorted Thermistor Alarm ............................... 34

4. Power Loss Alarm ........................................... 34

5. Door Open Alarm ............................................ 34

TABLE 1 - Model types ......................................... 35

Troubleshooting ............................................................ 36

VCC3 Inverter Diagnostic Codes ........................... 36

High Voltage Board ................................................ 37

Low Voltage Board ................................................. 38

Troubleshooting Guide ........................................... 39

30" All Refrigerator Schematic, Upper Section ...... 42

30" All Refrigerator Schematic, Lower Section ...... 43

36" All Refrigerator Schematic, Upper Section ...... 44

36" All Refrigerator Schematic, Lower Section ...... 45

Wiring Diagrams ........................................................... 46

Wiring 30" All Refrigerator Page 1 ......................... 46

Wiring 30" All Refrigerator Page 2 ......................... 47

Wiring 36" All Refrigerator Page 1 ......................... 48

Wiring 36" All Refrigerator Page 2 ......................... 49

Summary of Contents for Quiet Cool VCRB5301
















































Search results

Summary of Contents for Quiet Cool VCRB5301

Reviews:

Viking Quiet Cool VCRB5301, Service Manual, Page: 2 / 47

Search results

Summary of Contents for Quiet Cool VCRB5301

Reviews: