background image

ACTIVATE

CONTROLS

DISPLAY

OFF

Operation

©2012 Viking Preferred Service

9

To enter Sabbath mode, press and 

hold "ACTIVATE CONTROLS" pad 

then press and hold "DISPLAY 

OFF" pad, together for three 

seconds this will cause an audible 

three beeps, signifying that 

Sabbath mode has been entered.

Sabbath Mode

When Sabbath mode has been entered the 

display goes blank except for the "SAB", 

see illustration below, which will remain 

illuminated whether the door(s) are open or 

closed, it will not change state.

Sabbath mode is used to control the 

refrigerator without interior lights, LED 

display  changes and enunciators. Alarms are 

suppressed, you will not get visual or audible 

alarms during Sabbath mode, although they 

are recorded in memory and will be displayed 

upon exiting Sabbath mode.

The freezer/refrigerator outputs (compressor, 

fans,etc.) should not have an immediate 

reaction from a user action. If the control calls 

for an action because the door was opened 

or closed, the control shall delay its reaction 

randomly (15-25 seconds).

To exit "SABBATH" mode, press and hold 

"ACTIVATE CONTROLS" and then "DISPLAY 

OFF" together for three seconds, an audible 

three beeps will be heard and "SAB" on 

display will extinguish. The display will return 

to normal and any alarms will be visually and 

audibly displayed.

ACTIVATE

CONTROLS

DISPLAY

OFF

Fahrenheit to Celsius

Factory default for readout is 

Fahrenheit, to change to Celsius, 

press and hold "ACTIVATE 

CONTROLS" and then press and 

hold "DISPLAY OFF" for three 

seconds and 

o

F will change to 

o

C. 

To change back to Fahrenheit, 

repeat same steps. 

Summary of Contents for Quiet Cool VCRB5301
















































Reviews: