21
D. Keyless Entry Codes and One Time Use Keyless Entry Codes
E. Proximity Cards
F. 911 Calls
Keyless entry codes may be used by the tenants to provide keyless entry. The
K-1900-8-IP Series
phone can be programmed with a
combination of up to 1000* keyless entry codes or one time use keyless entry codes. The keyless entry codes can be programmed to
be from 1 to 6 digits in length. Each keyless entry code can be programmed to activate relay 1 and/or 2 in four different relay modes:
Momentary, Latch, Un-Latch and Toggle. To use a keyless entry code the tenant simply dials
“#”
followed by the entry code on the
K-1900-8-IP’s
keypad. After the one time use keyless entry code has been used, it is instantly cleared from the unit’s memory. This is
ideal for issuing keyless entry codes to service personnel, etc.
In the Single and Multi-Number Auto Dialer modes, keyless entry codes can be dialed while the handset is hung up or when the handset
is first lifted, when some delay has been programmed for Off Hook Dialing Delay.
Proximity cards can also be used by the tenants to provide keyless entry. The
K-1900-8-IP Series
phone can be programmed with up
to 1000* proximity card numbers. Each proximity card number can be programmed to activate relay 1 and/or 2 in four different relay
modes: Momentary, Latch, Un-Latch and Toggle. To use a proximity card, the tenant simply presents a preprogrammed proximity card
within range
**
of the proximity card reader attached to the
K-1900-8-IP Series
phone. A short beep will be heard from the card reader
indicating a card scan. If the card matches a valid preprogrammed card number the relay will be activated and the visitor can now open
the door or gate. Proximity cards can be scanned at anytime, even while a call is in progress.
The
K-1900-8-IP Series
phone is not intended to be an emergency phone and does not try to automatically handle users that dial “911”
after picking up the handset. In the Manual Dial Phone mode, the “911” dialed by the user is passed on to the phone system, so it is up
to the SIP phone system or provider to route the call properly. In the Single and Multi-Number Auto Dialer modes, a speed dial of “911”
can be programmed with primary and rollover phone numbers, to route the calls appropriately. Some delay must be programmed for Off
Hook Dialing Delay, to give the user time to dial the “911” before they are automatically routed to another number or hear 3 beeps.
*Note:
1000 is the total number of Keyless Entry Codes and/or Proximity Card numbers that can be programmed in the Entry Code
Database.
**Note:
Read range depends on the type of card and card reader being used.
Feature
Touch Tone
Command
Description
Momentarily
Activate Relay 1
,,
or
___ ___
Momentarily activate relay 1 (1 or 2 digits, factory set to
,,
).
Latch Relay 1
11
Latch* (continuously activate) relay 1.
Un-Latch Relay 1
10
Un-latch* (deactivate) relay 1.
Toggle Relay 1
1#
Toggle* relay 1 from last position.
Momentarily
Activate Relay 2
,
2 or
___ ___
Momentarily activate relay 2 (1 or 2 digits, factory set to
,
2).
Latch Relay 2
21
Latch* (continuously activate) relay 2.
Un-Latch Relay 2
20
Un-latch* (deactivate) relay 2.
Toggle Relay 2
2#
Toggle* relay 2 from last position.
Disconnect
#
Disconnects or forces the phone to hang up.
* Note:
Latching commands must be enabled in programming.
C. Remote Access Operation Commands
The following commands can be entered after answering a call from the entry phone. The commands can also be entered on an
inbound call to the entry phone. After calling into the entry phone and the unit auto answers or someone answers the call by lifting
the handset, one or two beeps will be heard. If the access code has been disabled (two beeps heard), you can now enter the Remote
Access Operation Commands below. If an Access code has been programmed (one beep heard), enter the Access code digits. With
the correct code entered, two beeps will be heard and you can now enter the Remote Access Operation Commands below. The
Relay Mode must be set to “Door Strike” to be controlled by these commands.
If the unit cannot register with the programmed SIP server, three error beeps will be heard in the handset every 30 seconds until
communication is restored. This alerts a potential user of a problem with the device that will prevent a phone call from being made.
You may silence the error beeps, per instance, by clicking the “Mute Current / Next Alarm” button in the Viking IP Programming Software
(see section
A
on page 7). The error beeps automatically re-enable once the unit is registered, to alert of any new problems that arise.
Troubleshooting
