5
1. Mount both plastic anchors in the wall.
2. Insert the sheet metal screws (#10) through
the mounting bracket into the plastic anchors.
3. Hang the clock on the mounting bracket.
4. Put the screw (4mm) through the hole on the
top of the clock into the hole at the top of the
mounting bracket.
1. Install Metal Mounting Bracket -
First, remove the metal mounting bracket from the inside of the double mount base by unscrewing the two (2)
6-32 x 1/2” screws located on the underside of the base (save these screws for step #3). Next, screw the metal mounting bracket to the wall or
ceiling in which the clocks are being installed. To mount to the switch box, screw the four (4) 6-32 x 1” screws supplied in the assembly kit through
the inner four holes of the metal mounting bracket to the wall or ceiling. Use the outer four holes to mount anchors to the wall or ceiling (both
anchors and screws for anchors not supplied in kit).
Note:
if using a plastic switch box, a ground wire must be routed through the switch box and into one (1) of the four (4) metal mounting bracket
screws in order to provide ground to the metal mounting bracket.
Note:
the metal mounting bracket MUST be secured by both the screws going to the switch box AND the anchors going into the wall.
2. Feed wiring through base and pole -
Take the wiring coming from the switch box and begin to feed it through the center of the base of the
mounting assembly until it emerges from the hole in the center of the clock adaptor. Make sure there is roughly 1.5’ - 2’ of wiring coming from the
switch box. Perform this task for both clocks.
3. Snap and screw base to metal mounting bracket
- Snap the base to the metal mounting bracket by first making contact with the lip in the upper
side of the base and the metal mounting bracket. When the base has been snapped onto the bracket, take the two (2) 6-32 x 1/2” pan head screws
that originally came installed on the base of the mounting assembly and screw them back into the two holes on the underside of the base to secure
the base to the metal mounting bracket.
4. Connect switch box wires to clock harness
- Take the wiring harness supplied with the clock and make all necessary connections between the
wiring harness and the switch box wires using wire nuts. Perform this task for both clocks.
5. Plug and secure wiring to clock
- Loosen and slip excess wiring through provided wire clamp (comes attached to each clock adaptor) and tighten
the clamp. After securing excess wiring, plug the jack at the end of the wiring into the appropriate jack on the back of the clock.
6. Attach and screw clocks to adaptors
- Find all four (4) tabs
located on each adaptor. Snap the clock onto the adaptor, making
sure all four (4) tabs on the adaptor are secured to the clock (if
installing battery powered clocks, make sure batteries are installed
at this point). After securing the clock to the adaptor with the tabs,
the clock should be able to rotate 5 degrees left and right. Rotate
to align the clocks with the ceiling or wall. Secure its position by
using the four (4) 6-19 x 7/16” screws that come attached to the
clock adaptor from the factory and screw them into the four (4)
tabs on the adaptor.
CL-A12
(12” Analog Clock)
CL-DMA12 / CL-DMA16
(Double Mount for 12” and
16” Analog Clocks)
CL-DMA12 / CL-DMA16 Specifications
Housing:
30% Glass Reinforced ABS Plastic
Shipping Weight:
CL-DMA12: 4.2 lbs (1.91 kg)
CL-DMA16: 6.1 lbs (2.77 kg)
CL-A16
(16” Analog Clock)
IMPORTANT: We highly recommend installing the CTG-2 Clock/Tone Controller and CL-RFT Transmitter before
the installation of the CL Series clocks.
IMPORTANT: Remove pin from back of clock before installing batteries.
In order to install the
CL-A12/16
clocks, simply remove the battery cover, and install two (2) D cell batteries
(recommended battery type: Duracell PROCELL). After installation of the battery, replace the battery cover and the
clock should start correcting within five (5) minutes. If the clock does not automatically correct itself, then manually press
the Transmit/Receive switch once on the clock closest to the clock that isn’t working. The second hand will go to 8
notifying the user that the clock is transmitting a signal. Then go to the clock that isn’t working and press the
Transmit/Receive switch twice. The second hand will go to 4 notifying the user it is looking for a signal. This should get
the signal to the clock.
Note:
The Transmit/Receive signal window is 10 minutes and multiple clocks can receive from
the transmitting clock during that period.
For metal mounting bracket: Use anchor that can support 50 lbs with a maximum screw size of 10/1.5”
B. Wall Mounting the CL-A12 and CL-A16
C. Double Mount CL-DMA12 and CL-DMA16 for the CL-A12 and CL-A16 Clocks
D. Operation
