Viking CL-A12 Product Manual Download Page 11

Page: 11 / 12

2. Troubleshooting

What happens if the clock doesn’t power up?

Make sure the wiring is correct. The power should be on the orange and yellow wires of the harness. The middle (green) wire is
ground. If the wiring is correct, take a volt meter and measure the voltage. The voltage should be between 14 - 28 volts.

What happens if the clock does not receive the signal?

Take the clock within close proximity to the transmitter and power the clock. If the clock does not correct, call Viking technical
support at (715) 386-8666.

I have a location with a marginal signal. What should I do?

Move your Transmitter closer to the location or add a Repeater (

CL-RFT

with JP1 and JP2 in “Repeater” position, see page 3)

between the Transmitter and the location with marginal signal.

Description:

Optional wire guard for use with

the Viking

CL-A12

12” round analog clock

Dimensions:

18.75” x 16” x 5” (47.63cm x

40.64cm x 12.7cm)

Shipping Weight:

3.9 lbs (1.77 kg)

Wire:

3, 6 and 9 gauge

Finish:

Zinc plated epoxy, lacquered

baked clear coat

Description:

Optional wire guard for use with

the Viking

CL-A16

16” round analog clock

Dimensions:

23” x 19” x 5” (58.42cm x

48.26cm x 12.7cm)

Shipping Weight:

5.2 lbs (2.36 kg)

Wire:

3, 6 and 9 gauge

Finish:

Zinc plated epoxy, lacquered

baked clear coat

Description:

Optional wire guard for use

with the Viking

CL-D2

CL-D4

digital clock

Dimensions:

18” x 15” x 6.5” (45.72cm x

38.10cm x 16.51cm)

Shipping Weight:

4.6 lbs (2.09 kg)

Wire:

3, 6 and 9 gauge

Finish:

Zinc plated epoxy, lacquered

baked clear coat

CL-WGA12

(Front View)

CL-WGA12

(Side View)

18.75" Diameter

5.0"

CL-WGA16

(Front View)

CL-WGA16

(Side View)

23" Diameter

5.0"

CL-WGD4

(Front View)

CL-WGD4

(Side View)

18.0"

6.5"

15.0"

CL-WGA12 / CL-WGA16 Wire Guards

CL-WGD4 Wire Guard

Specifications for CL-WGA12

Specifications for CL-WGA16

Specifications for CL-WGD4

Summary of Contents for CL-A12













Search results

Summary of Contents for CL-A12

Reviews:

Related manuals for CL-A12

Brands by name

Popular brands

Viking CL-A12, Product Manual

Search results

Summary of Contents for CL-A12

Reviews:

Related manuals for CL-A12

Brands by name

Popular brands