background image

MODEL VG06045

4

LEFT INSTALLATION

RIGHT INSTALLATION

DOOR

DOOR

DOOR

FIXED PANEL

FIG. 1A (GLASS CONFIGURATION DIAGRAM)

DOOR

FIXED PANEL

WARNING

VIGO STRONGLY RECOMMENDS THIS INSTALLATION BE COMPLETED BY A LICENSED

PROFESSIONAL. INSTALLATION OF DOOR UNIT REQUIRES AT LEAST TWO PEOPLE.

REQUIRED TOOLS:

- Square and/or Phillips #1 and #2 screwdriver
- Flat head screwdriver
- Electric drill; 1/4" drill bit (According to wall)
- Level
- Measuring tape
- Non permanent pencil
- Clear silicone caulking
- Utility knife; Hacksaw

If needed, remove the plastic layer of the base border. Do not remove the plastic layer off the plastic platform of the

base. Wall and base joints must be siliconed properly. To fit shower door into your opening cut structural rail on door

side only!

BEFORE INSTALLATION

See suggestion of configuration below.

PLEASE NOTE:

THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALLED TO THE RIGHT OR LEFT
SIDE. (SEE CONFIGURATION DIAGRAM BELOW)

!

INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS
BREAKAGE AND CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH.

- Handle fragile items with care to prevent personal injury or material damage.
- The glass panels are tempered and cannot be cut.  Never attempt to do so.
- Always rest glass on a level surface

BEFORE STARTING

Compare items on your invoice with what you have received. Carefully review the Parts List on page 2. If any
items are missing, please call Vigo Industries at 1-866-591-7792. Please check our website at

www.vigoindustries.com for additional information or instructional videos.

IMPORTANT

Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support the shower door

enclosure. You should use the wood framing from behind the face edge of the stall to provide a secure

mounting to the door. Apply a bead of silicone between the walls and base of the stall.
For optimum performance, you should install the shower door perfectly level on a level surface. By  not leveling

the unit during construction the unit may leak causing possible water damage.

Summary of Contents for VG06045 Series
























Reviews: