background image

29

5797 342 - 01

Vitoflex 300-RF Service & Maintenance

Maintenance

 Servicing the Boiler

 

(continued)

Component, activity

Interval

300 

hours

900 

hours

Every 6 

months

Annually

Heat exchanger 

B

Check system pressure at pressure gauge (minimum pressure, water shortage).

O

Check thermally activated safety valve for tightness.

O

Ignition system 

F

Check ignition pipe for blockages and clean if necessary.

O

Pneumatic cleaning system (optional)

Check valves for tightness.

O

Compressor system (optional)

Service the compressor system in accordance with the compressor operating 

instructions. 

Observe information on compressor.

O

(Interval in accordance with the 

compressor operating instructions)

Flue gas path (optional)

Check chimney draught regulator for ease of operation.

O

Information on the compressor

If the compressor is operating continuously, this indicates

that there is a leak in the compressed air system.

Check supply lines and valves for leaks.

In the case of on-site supply of compressed air, ensure

that the compressor is suitable for continuous operation

or can be prevented from operating continuously.

 Cleaning the Boiler

Information on cleaning the boiler

Note:

 Cleaning work may also be carried out by a local  

 chimney 

sweep.

Prior to cleaning

Switch off the system via the button. 

Then start the cleaning function via the 

 button.

The function can be found in the “Charging” parameters/

under the “Ash removal” tab, see operating instructions.

Cleaning function enabled:

 Flue gas fan operates at 50%.

 Infeed grate is moving.

Dirt and deposits can damage the boiler. Clean the outside

of the heating system as required. Have the inside of the

heating system cleaned at least once a year by contractors.

IMPORTANT

Summary of Contents for Vitoflex 150-RF





































Reviews: