Vidikron Vision 140 Installation & Operation Manual Download Page 32

Page: 32 / 116

Installation

Vision Model 140/150 Installation/Operation Manual

PRE

IMINAR

•

Do not drop the remote control or expose it to moisture or high temperature.

•

The remote control may malfunction under a fluorescent lamp. If that occurs, move the
VHD Controller away from the fluorescent lamp.

•

Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the VHD Controller or projector.

•

If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.

•

The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.

•

Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the VHD Controller, and repeat the operation.

Summary of Contents for Vision 140





















































































































Search results

Summary of Contents for Vision 140

Reviews:

Related manuals for Vision 140

Brands by name

Popular brands

Vidikron Vision 140, Installation & Operation Manual

Search results

Summary of Contents for Vision 140

Reviews:

Related manuals for Vision 140

Brands by name

Popular brands