Videofied XV Installation Manual Download Page 17 | Manualshive

Page: 17 / 21

background image

EN.V1

Installation manual XV

17

The option « WARNING BEEP » is triggered during scheduled arming delay. To configure this option,
go to:

CONFIGURATION (Level 4) + [YES]



AREAS AND DEVICES + [YES]



WARNING BEEPS +

[YES]

6. Level test GPRS error

IMPORTANT:

The PIN of the SIM card has to be deactivated or 00000.

7. Specials codes

Codes

Action

999999

Maintenance request - GPRS transmission

999997

Give the information that the panel detects main power or not.

999991

The panel will send a test alarm to the first IP address configured in the menu
“Address Server”. In case of failure the panel will not stay “blocked in transmission”
Very long time. This code can be use just to test the good transmission to the
monitoring station.

«
...
15
16
17
18
19
...
»

Summary of Contents for XV






















Reviews:

No comments

Related manuals for XV

Brand: Sven Pages: 12

Brand: Abode Pages: 5

SG2 BASE Series

Brand: Datalogic Pages: 62

Brand: i3 International Pages: 2

Brand: i3 International Pages: 2

Brand: i3 International Pages: 22

Brand: i-PRO Pages: 12

Brand: i-PRO Pages: 27

Brand: Walabot Pages: 9

Brand: i-PRO Pages: 24

Brand: i-onik Pages: 59

Brand: Rafiki Protection Pages: 32

Brand: Ultra Products Pages: 1

Brand: Barnstead|Thermolyne Pages: 56

Brand: ACTi Pages: 19

Brand: HAKO Pages: 6

Brand: Abicor Binzel Pages: 2

Brand: S Fire Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands