Victron energy Phoenix Smart IP43 12/30 Manual Download | Manualshive

Page: 28 / 59

background image

6.4. Bluetooth

6.4.1. Changing the PIN code

To prevent an unauthorised Bluetooth connection, it is highly recommended to change the default PIN code.

To change the Bluetooth PIN code:

a. Complete initial Bluetooth pairing and connection using the default PIN code (000000)

b. Access the ‘device options’ by selecting the 'settings' icon (gear) in the top right corner, then the 'device options' icon (three

vertical dots).

c. Open the 'Product info' page by selecting 'Product info’.

d. Beside ‘Pin code’ select ‘CHANGE’ to open the ‘Change PIN code’ window.

Phoenix Smart IP43 Charger

Page 26

Setup

«
...
26
27
28
29
30
...
»

Summary of Contents for Phoenix Smart IP43 12/30




























































Reviews:

No comments

Related manuals for Phoenix Smart IP43 12/30

Brand: Fein Pages: 42

Brand: Hans Pages: 2

Brand: Samsung Pages: 64

Brand: Samsung Pages: 9

Brand: Samsung Pages: 3

Brand: Samsung Pages: 10

Brand: HITEC Pages: 24

Brand: T'nB Pages: 18

Brand: Braun Pages: 144

Brand: Telwin Pages: 37

Brand: EINHELL Pages: 116

Brand: Ripmax Pages: 4

Brand: Ultra Power Pages: 32

Flex-Force Power System

Brand: Toro Pages: 12

Brand: Schumacher Electric Pages: 112

Brand: Tripp Lite Pages: 2

Brand: dji Pages: 54

Brand: Ripmax Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands