Victron energy Phoenix Smart IP43 12/30 Manual Download

Page: 58 / 59

9. Technical specifications

Specification

12/30

(1+1) & (3)

12/50

(1+1) & (3)

24/16

(1+1) & (3)

24/25

(1+1) & (3)

Input voltage - AC supply

85 - 265VAC (full power from 100VAC, startup from 90VAC)

Input frequency - AC supply

45 - 65Hz

Input voltage - DC supply

290 - 375 VDC

Power factor

>0.99

Max Efficiency - 230VAC / 120VAC

95% / 93%

94% / 92%

96% / 94%

96% /94%

Charge voltage - Absorption / Float / Storage

Normal: 14.4V / 13.8V / 13.2V

High: 14.7V / 13.8V / 13.2V

Li-ion: 14.2V / N/A / 13.5V

Normal: 28.8V / 27.6V / 26.4V

High: 29.4V / 27.6V / 26.4V

Li-ion: 28.4V / N/A / 27.0V

Temperature compensation (N/A for Li-ion)

-16mV/°C

-32mV/°C

Charge algorithm

6-stage adaptive (3 stage for Li-ion)

Max output current - Normal mode

30A

50A

16A

25A

Max output current - Low current mode

15A

25A

12.5A

Max output current - Starter battery

4A (1+1 output models only)

Back drain current

<1mA

Max battery capacity (recommended)

300Ah

500Ah

160Ah

250Ah

Min battery capacity - Normal mode

Lead: 120Ah

Li-ion: 60Ah

Lead: 200Ah

Li-ion: 100Ah

Lead: 64Ah

Li-ion: 32Ah

Lead: 100Ah

Li-ion: 50Ah

Min battery capacity - Low current mode

Lead: 60Ah

Li-ion: 30Ah

Lead: 100Ah

Li-ion: 50Ah

Lead: 32Ah

Li-ion: 16Ah

Lead: 50Ah

Li-ion: 25Ah

Data communication

VE.Direct and Bluetooth (via VictronConnect app)

Bluetooth power and frequency

-4dBm | 2402 - 2480MHz

Remote on/off

Yes (2 pole terminal)

Programmable relay

Yes (SPDT - 5A up to 250VAC / 5A up to 28VDC)

Operating temperature

-20 to +60°C (0 - 140°F) Full rated output up to 40°C

Max humidity

95%

Enclosure

Material and colour

Aluminium | Blue RAL 5012

AC connection

IEC 320 C14 inlet with retainer clip (AC cord ordered separately)

Battery connection

Screw terminals 16 mm² (AWG6)

Number of battery connections

(1+1) models: 2 (2nd output via 2 pole terminal) | (3) models: 3

Protection category

Electronic components: IP43 | Connection area: IP22

Weight

2.7 kg (6.0 lbs)

Dimensions (h x w x d)

180 x 249 x 116mm (7.1 x 9.8 x 4.6 inch)

Compliance standards

Safety

EN 60335-1, EN 60335-2-29

Emission

EN 55014-1, EN 61000-6-3, EN 61000-3-2

Immunity

EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3

Vibration

IEC68-2-6:10-150Hz/1.0G

Phoenix Smart IP43 Charger

Page 56

Technical specifications

Summary of Contents for Phoenix Smart IP43 12/30




























































Search results

Summary of Contents for Phoenix Smart IP43 12/30

Reviews:

Related manuals for Phoenix Smart IP43 12/30

Brands by name

Popular brands

Victron energy Phoenix Smart IP43 12/30, Manual

Search results

Summary of Contents for Phoenix Smart IP43 12/30

Reviews:

Related manuals for Phoenix Smart IP43 12/30

Brands by name

Popular brands