Vicon HOV Manual Download Page 8

EN - English - I

nstruc

tions manual

6

The pre-wired heating element should be positioned 
between the 2 dissipators before attachment to 
ensure contact and hence guarantee correct heat 
diffusion.

Fig. 04 

Pass the heating wire under the fixing slide of the 
camera. Insert the 2-pin connector at the end of the 
cable into the correspondent support circuit socket, 
identified by J3 HEATER.
Reposition the internal support slide and close the 
housing.

6.1.6  Camera power supply installation

 

h

Not usable in housings with wiper device 
installed.

This chapter describes how to install the camera 
power supply option into the housing. There are 
2 types of camera power supply depending on 
requirements.
One model has an input voltage from 100-240Vac 
with an output voltage of 12Vdc, 1A.
The other has an input voltage of 230Vac and an 
output voltage of 24Vac, 400mA.

Fig. 05 

IN 100-240Vac - OUT 12Vdc.

Fig. 06 

IN 230Vac - OUT 24Vac.

Open the housing as described before.

6.1.4  Board and connection

 

h

Connect the safety earth to the relative 
terminal of the J1 connector.

BOARD DESCRIPTION

J1

Input power supply terminal: 100-240Vac or 
24Vac, 12Vdc

J2

Output power supply terminal (same voltage 
coming from J1)

J3

Output terminal for heating 

J4

Anti-opening switch terminal (optional)

J5

Camera power supply output terminal *

J7

Connector for power supply **

J8

Connector for fan

Tab. 01  * The camera output voltage can be 12Vdc or 24Vac 

in relation to the type of power supply installed (

"6.1.5 

Heater installation", page 6

). In case of jumper 

installation (only 12Vdc or 24Vac versions) the J5 
terminal presents the same voltage applied at input J1. 
** Refer t

"6.1.5 Heater installation", page 6

 to install 

a 12Vdc or 24Vac power supply.

J2 - OUT

J1 - IN

J5 - Camera

OUT

J8 - Blower

J3 - Heater

J7 - Power supply

SW1 - Power supply

J2 - Terminal

Fig. 03 

6.1.5  Heater installation

This section describes how to install the heater option 
in the housings not provided with. Heaters can be 
supplied with working voltages of 12Vdc/24Vac 
or 115/230Vac and include the pre-wired heating 
element suitable for the working voltage, metal 
dissipators and kit fastening screws.
Open the housing as described before. Fix the heater 
kit to the prearranged points on the body of the 
housing.

Summary of Contents for HOV















Reviews: