manualshive.com logo in svg

Viavi SmartClass OLP-85 Series, Operating Manual, Page: 19 / 84

Share
Download
Viavi SmartClass OLP-85 Series Operating Manual Download Page 19

OLP-85/OLP-85P

19

U

NPACKING

 

THE

 

INSTRUMENT

3  G

ETTING

 S

TARTED

NOTE:

Rechargeable AA batteries will not be recharged in the 

instrument. For AA-type rechargeable batteries please use an 

external charger.

It is not possible to charge the rechargeable AA batteries or the 

RBP2 Li-Ion Battery Pack via the USB interface.
If the PS4 Universal AC/DC Power Supply and the USB interface 

are both connected, the instrument is powered by the PS4 

Universal AC/DC Power Supply.

Deep discharge

A rechargeable battery that appears to be dead (unit will not 

turn on even when connected to external power) may well be in 

a deep discharge state. It can be fully charged with the following 

charging cycle:

1.

Plug in the power cord for 1–1.5 hours.

Battery should be partly charged now.

2.

Switch the power on.

If the instrument starts: Let the battery fully charge.

– or –

If the instrument does not start: 

Unplug power cord, plug it back in and repeat steps 1 and 2.

NOTE:

If the battery is completely deep-discharged, this cycle might 

need to be repeated up to 3 times.

General tips on using batteries

• Always handle batteries with care.

• Do not drop or damage the batteries or expose them to 

excessively high temperatures.

• Do not store the batteries for more than one or two days at 

very high temperatures (e.g. in a vehicle), either separately or 

inserted in the instrument.

• Do not leave discharged batteries in the instrument for a long 

time if it is not being used.

Summary of Contents for SmartClass OLP-85 Series





















































































Reviews:

No comments