background image

 

11 

Information for customer 

 

Packaging identification 
 
PE Plastic sacks, folie, corrugated board, iron and plastic fix line 

Assessment reference 

 
Identification of principal materials used. Paper, Polyethylene, iron, wood 

 
Part 1: Summary of assessment 

Standard/Report 

Assessment requirement 

Claim 

Note 

1.1  Prevention by source 

reduction 

 

YES 

 

1.2  Heavy metals and 

ensure  below  maximum  permitted  levels  for 
components  
(CR 13695-1) 

YES 

 

1.3  Other 

noxious/hazardous 
substances 

ensure in compliance with  
(

Č

SN 77 0150-2, EN 13428) 

YES 

 

Reuse 

ensure reusability in all terms of the standard 
for the functional packaging unit (EN 13429) 

NO 

 

3.1  Recovery by material 

recycling 

ensure  recyclability  in  all  terms  of  the 
standard for the functional packaging unit (EN 
13430) 

YES 

 

3.2  Recovery in the form of 

energy 

ensure that calorific gain is achievable for the 
functional packaging unit  
(EN 13431) 

YES 

Iron - NO 

3.3  Recovery by 

composting 

ensure  compost  ability  in  all  terms  of  the 
standard for the functional packaging unit (EN 
13432) 

NO 

 

 
NOTE   Conformity with EN 13427 requires affirmative responses to sections 1.1; 1.2; 1.3 and to at least one of 

3.1; 3.2; 3.3. In addition, where a claim of reuse is made section 2 should also record affirmative 
responses. 

 
Part 2: Statement of conformity 
In the light of the assessment results recorded in part I above, this packaging is claimed to comply with the 
requirements of EN 13427. 

 

 

 

Summary of Contents for ViaKON 24 B













Reviews: