Vexar CD32Ml Owner'S Operation And Installation Manual Download Page 9

www.desatech.com

111916-01F

9

INSTALLATION 

Continued

ELECTRICAL HOOKUP AND 
REMOTE RECEIVER DIAGRAM

An outlet box with two receptacles (see Figure 9) has 

been supplied for your convenience and is located 

inside on the lower right side of the fireplace. 
The remote control receiver is factory wired and 

connected to the convertible gas valve as shown 

in Figure 10.

Figure 9 - Duplex Outlet

Three-prong Plug

Figure 10 - Remote Control Receiver 

Outlet Box

Remote 
Control 
Receiver

Convertible 
Gas Valve

GAS SUPPLY TESTING

NOTICE:  This  section  is  in-

tended as a guide for qualified 

technicians installing gas to the 

appliance.

 WARNING: Do not connect 

appliance before pressure test-

ing gas piping. Damage to gas 

valve may result and an unsafe 

condition may be created.

The appliance and its individual shutoff valve must 

be disconnected from the gas supply piping system 

during any pressure testing of that system at test 

pressures in excess of 1/2 psig (3.5 kPa). 

The appliance must be isolated from the gas sup-

ply piping system by closing its individual shutoff 

valve during any pressure testing of the gas supply 

piping system at test pressures equal to or less than 

1/2 psig (3.5 kPa).
The gas control valve is secured underneath the 

firebox. Two 1/8" ports are provided on the gas 

control valve for pressure test gauge connections 

(see Figure 11).

Figure 11 - Gas Control Valve

ON/OFF 
Knob

Pilot Adjustment

Inlet 
Pressure Outlet 

Pressure

Flame 
Adjustment Knob

Pilot Gas Line 
Do Not Kink

To Pilot 
Burner

To Main
Burner

GAS LINE HOOK-UP

  WARNING:  Gas  line  hook-

up should be done by your gas 

supplier  or  a  qualified  service 

person.

 WARNING: Before you pro-

ceed, make sure your gas supply 

is OFF.

An equipment shutoff valve has been included in 

the fireplace's gas supply system. However, con-

sider installing an extra shutoff valve outside the 

applianceʼs enclosure (check local codes), where 

it can be accessed more conveniently with a key 

through a wall as shown in Figure 12.

Figure 12- Typical Exterior Wall Gas 

Shutoff Installation

Key

Extension

Shutoff 
Valve

Summary of Contents for CD32Ml

























Reviews: