Vexar CD32Ml Owner'S Operation And Installation Manual Download Page 7

www.desatech.com

111916-01F

7

INSTALLATION

 WARNING: Read all instruc-

tions completely and thoroughly 

before  attempting  installation. 

Failure to do so could result in 

serious  injury,  property  dam-

age or loss of life. Operation of 

improperly installed and main-

tained  venting  system  could 

result in serious injury, property 

damage or loss of life.

NOTICE: Failure to follow these in-

structions will void the warranty. 

VENTING INSTALLATION 
PRECAUTIONS

Consult local building codes before beginning the 

installation. The installer must make sure to select 

the proper vent system for installation. Before 

installing  vent  kit,  the  installer  must  read  this 

fireplace manual and vent kit instructions.
Only  a  qualified  service  person  should  install 

venting system. The installer must follow these 

safety rules:
•  Wear gloves and safety glasses for protection
•  Use extreme caution when using ladders or 

when on roof tops

•  Be aware of electrical wiring locations in walls 

and ceilings

The following actions will void the warranty on 

your venting system:
•  Installation of any damaged venting component
•  Unauthorized modification of the venting system
•  Installation of any component part not manu-

factured or approved by DESA 

•  Installation other than as instructed by these 

instructions

 WARNING: This gas fireplace 

and  vent  assembly  must  be 

vented directly to the outside. The 

venting system must NEVER be 

attached to a chimney serving a 

separate solid fuel burning appli-

ance. Each gas appliance must 

use a separate vent system. Do 

not use common vent systems.

  WARNING:  Horizontal  sec-

tions of this vent system require 

a minimum clearance of 2" from 

the top of the pipe and 1" mini-

mum to the sides and bottom. 

Vertical sections of this system 

require a minimum of 1" clear-

ance  to  combustible  materials 

on all sides of the pipe.

VENTING INSTALLATION

1.  Install elbow to fireplace collar adapter located 

on back of the unit at a 45° angle. Slide elbow 

over collar and twist to lock. Check to insure 

proper connection (see Figure 6).

2.  Continue  to  install  remainder  of  pipe  for 

desired installation. Make sure each section 

is twist-locked securely.

3.  When installation of vent pipe is complete, in 

stall vent termination. Depending on the loca-

tion of your fireplace, you will vent vertically 

or horizontally. 

4.  Allow 1" of pipe to protrude from internal 

wall,  depending  on  wall  thickness.  See 

Figure 7, page 8.

5.  For horizontal installation, an optional siding 

standoff may be installed between the vent cap 

and the exterior wall. Secure horizontal vent cap 

to standoff. Secure standoff/vent cap assembly 

to wall (see Figure 7, page 8). Do not seal termi-

nation to vent pipe. The vent termination must 

be removable for service pipe inspection. 

Figure 6 - Venting Installation

Female 
Locking Lugs

Male 
Locking Lugs

Vertical Flue 
Restrictor 
(For Vertical 
Venting 
Application)

Summary of Contents for CD32Ml

























Reviews: