Vetus GHX Installation Manual Download | Manualshive

Page: 16 / 24

background image

16

380602.01

vetus®

Installation manual Generator Sets GHX / GLX

3.3.4 Seawater strainer

Install raw water strainer in
an area where it will be easily
accessible for inspection and
cleaning. Strainer should be
installed in water inlet hose
after the sea cock (water inlet
valve) to allow operator to shut
off water when cleaning strain-
er.

3.3.5 Fittings

IMPORTANT

If other/more fittings or pipes then included in the scope of supply are needed use only
bronze hardware.

If more lenght of hose is needed then included in the scope of supply use only MARINE-
WATER HOSE, steel reinforced and suitable for 2.5 bar (35 psi) both suction or pressure.

Use sealing compound or tape at all connections to prevent air leaks. The neoprene impeller in the raw water pump
should never be run dry. All hose joints should be double clamped with 304/316 stainless-steel hose clamps. T-bolt
clamps are even better but must be 304/316 stainless.

WL

min. 15 cm

(6”)

Raw water

inlet connection

«
...
14
15
16
17
18
...
»

Summary of Contents for GHX

























Reviews:

No comments

Related manuals for GHX

Brand: YMGI Pages: 64

IMP-C1000-SFP-bt-24 Series

Brand: ANTAIRA Pages: 2

Brand: Bang & Olufsen Pages: 12

Brand: B&B Electronics Pages: 53

Brand: Hama Pages: 40

Brand: National Communications Pages: 20

Brand: HEIDENHAIN Pages: 16

Brand: Mastervolt Pages: 28

Brand: Uhlenbrock Elektronik Pages: 4

Brand: East Pages: 66

Brand: KTI Networks Pages: 25

Brand: Xantrex Pages: 41

Brand: Xantrex Pages: 92

Brand: Xantrex Pages: 84

GT2.8-AU-QC-230

Brand: Xantrex Pages: 90

Brand: TOYODenki Pages: 156

Brand: RTI Pages: 2

Brand: Micromega Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands