VESDA VESDA-E VES-A00-P Product Manual Download

Page: 37 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

Upright

Detector

Inverted

Detector

Figure 4-28: Slide detector to the left

Rotate the detector clockwise to position the large end of the detector’s top-left, or top-right for an
inverted detector, keyhole over the head of screw B. Push the detector to the wall (Figure 4-29).

Upright

Detector

Inverted

Detector

Figure 4-29: Position detector on the second screw

Rotate the detector anticlockwise, or clockwise for an inverted detector, to lock the detector on to the
screw (Figure 4-30).

Upright

Detector

Inverted

Detector

Figure 4-30: Rotate the detector

12. Insert an M4 screw at the small end of the detector’s bottom-left, or bottom-right for an inverted detector,

keyhole (Figure 4-31).

Summary of Contents for VESDA-E VES-A00-P





























































































































Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands

VESDA VESDA-E VES-A00-P, Product Manual

Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands