background image

VESDA by Xtralis 

 

VESDA Sensepoint XCL 

– Large Bore Quick Start Guide 

 

35564_00 

3. 

Turn over the detector module and locate the terminal blocks on the back. Remove the terminal 
blocks, pulling them toward the centre of the module. 

 

4. 

Connect the cable to the appropriate terminal block, referring to section 3 depending on the version. 
Strip and insert the end of each wire into the corresponding terminal hole, and tighten the terminal 
screw, using a flat-blade terminal screwdriver until the wire is secured. 

5. 

Replace the terminal blocks in their correct positions. 

4.4 

Ground Connections 

Effective grounding is crucial to ensure stable Modbus communications and to limit the effects of radio 
frequency interference. Ground points are provided inside the back box. In order to prevent false readings or 
alarms as a result of ground loops, ensure that the shield of all cables is grounded at a single point, 
preferably at the controller. 

Note: 

Any earth regime must avoid earth loops. 

 

4.5 

Securing Detector Module and Flow Cap 

 

1. 

Position the detector module with the Flow Cap onto the back box ensuring that the Status Indicator is 
in the top left-hand corner when viewed from the front. 

2. 

Tighten the four retaining screws using a No. 2 Phillips screwdriver to secure. 

3. 

Where used, tighten the sealing nut of the cable gland to secure the cable. Refer to the cable gland 
manufacturer’s instructions. 

 

 

www.acornfiresecurity.com

www.acornfiresecurity.com

Summary of Contents for Sensepoint XCL











Reviews: