background image

VESDA Sensepoint XCL 

– Large Bore Quick Start Guide 

 

VESDA by Xtralis 

35564_00 

 

Introduction 

 

Read and understand the VESDA Sensepoint XCL 

– Large Bore ASD System Installation Manual (Doc. No. 

35563) before installing, operating or servicing this product. 

Specifications 

Power Supply 

DC input voltage (nominal) 

24 V DC

1

 

AC input voltage (nominal) 

24 V AC

2

, 50/60 Hz 

Inrush current 

Less than 850 mA 

Maximum Power Consumption 

mA Versions 

< 1.2 W (toxic), <1.7 W (flammable and CO

2

Modbus versions 

< 0.7 W (toxic), <1.7 W (flammable and CO

2

Relay versions 

Additional 0.6 W 

Outputs

3

 

Analog output 

0 to 22 mA sink or source (configurable) 

Digital output 

Modbus RTU 

Relay output 

2 Relays (fault, alarm) Rated at 24V DC, 240V AC @5A 

Operating Environment 

Operating temperature 

−20 to 50°C (−4 to 122 °F) 

Storage temperature 

0 to 30°C (32 to 86 °F) 

Humidity 

0 to 99% (non-condensing)

4

 

Atmospheric pressure 

90 to 110 kPa 

Ingress protection 

IP65 / Type 4 (in accordance with NEMA 250) 

Installation category 

II (UL/CSA/IEC/EN 61010-1) 

Pollution degree 

2 (UL/CSA/IEC/EN 61010-1) 

Cable Gland 

Inner / Outer knock-out 

M20 or ½ NPT / M25 or ¾ NPT 

Sampling Pipe  

Outer diameter 

25 mm (0.98 in) / 27mm (1.06 in)  

                                                      

1

 mA versions: 11 to 32 VDC, Modbus versions: 9 to 32 VDC 

2

 20 to 27 VAC 

3

 Dependent on version 

4

 CAT version 10 to 90% RH. Operating the detector outside this range may result in increased drift and reduction in detector accuracy

 

www.acornfiresecurity.com

www.acornfiresecurity.com

Summary of Contents for Sensepoint XCL











Reviews: