background image

VES Andover Ltd Eagle Close Chandlers Ford Ind. Est Eastleigh Hampshire SO53 4NF
Tel: 08448 15 60 60  Fax: 02380 261204  E-mail: [email protected] Web: www.ves.co.uk

ecovent 

NRG

 Air Handling Units

Installation, Operation and Maintenance Manual

1

This manual must be read in full before Installation, Operation and Maintenance
of the units supplied

Please ensure that this document is passed to the end user. This manual forms an integral part of 
the product and should be kept for the working life of the product. Additional copies of this
and supporting documents are available by contacting VES or by visiting 

www.ves.co.uk

 and

following the ’Download O & M’s’ link.

The following symbols used within this document refer to potential dangers or advice for safe
operation

Indicates hazards associated with electric current and high voltages

Indicates hazards that require safety advice for personnel and/or potential unit/property damage

Indicates important information

 Page

Introduction 1

Nomenclature 2

Receipt of Goods & Handling 

3

Installation 3

Standard Wiring & Fan Installation 

10

Maintenance 14

Declaration of Conformity 

15

Extended Warranty 

16

The 

ecovent NRG

 series are a range of air handling units, direct and inverter driven, with duties 

up to 2.5m³/s. Suitable for either plantroom, ceiling void or external locations, each unit will have 
been supplied with either no pre-wiring, pre-wired to an external isolator or with fi tted control 
panel as specifi ed at the time of order.
The standard operating temperature of these units is –20 to +35°C.

For further technical details regarding dimensions and weights, contact VES on 

08448 15 60 60

quoting the sales order (SO) number and the unit type as found on the unit nameplate or visit 

www.ves.co.uk

.

VES Ref. ID.826

February 09

Important

Introduction

1
2
3
4
5
6
7
8

1

Summary of Contents for ecovent NRG

















Reviews: