VERTO 50G271, Manual

Page: 9 / 64

9
TRANSLATION OF ORIGINAL MANUAL
CORDLESS DRILL DRIVER
50G271
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
• Use hearing protection when operating the device. Noise
hazards may cause hearing loss.
• Use additional handles supplied with the power tool.
Loss of control may cause operator personal injury.
• Do not change direction of spindle rotation when the tool is
operating. Otherwise the power tool may get damaged.
ADDITIONAL RULES FOR SAFE DRILL OPERATION
• Use only recommended battery and charger.
• A lways keep the battery away from sources of fire. Do not leave
the battery for a long time in high temperature (in direct sunlight,
in proximity of heaters and wherever the temperature exceeds
5 0° C ).
• The battery charging time cannot be longer than 8 hours,
otherwise the battery may be damaged.
• A void charging the battery in temperature lower than 0° C .
• C harger supplied with the drill is designed for operation with this
product only. Do not use it for other purposes.
• Do not put any metal objects into the charger.
• Do not change direction of spindle rotation when the tool is
operating. Otherwise drill may be damaged.
• Use soft, dry cloth to clean the drill. Never use detergents or
alcohol.
• Disconnect charger from power supply before cleaning.
• If you intend to charge more than one battery successively, make
a
3 0 minute break between charges.
• Recharge the battery only after it is fully discharged.
• Do not recharge the battery after short use of the drill.
SPECIAL SAFETY CONDITIONS FOR CHARGER
OPERATION
• Keep this manual. It contains important drill use and safety
instructions.
• Before using the charger, read all relevant information contained
within this manual, see markings on the charger and the product
it is designed for.
• To reduce the risk of potential body injury use the charger for
charging lithium-ion batteries only. Other type batteries may
explode and cause personal injury or material damages.
• Do not expose the charger to humidity or water.
• Use of any connecting elements not supplied or not recommended
by the manufacturer of the charger may cause fire, personal injury
or electric shock.
• Make sure the power cord is not located in a pathway, is not
exposed to treading or other danger (e.g. strong tension).
• Do not use extension cord unless absolutely necessary. Use of
improper extension cord may cause fire or electric shock. If it is
necessary to use extension cord, first make sure that:
– E xtension cord socket matches plug prongs of the original
charger power cord.
– E xtension cord is in good technical condition.
• Do not use the charger with damaged cord or plug. Damage
should be repaired by a qualified person.
GB
• Do not use the charger after it has been hit, dropped or otherwise
damaged.
E ntrust the testing and potential repair to authorized
service workshop.
• Do not try to dismantle the charger. A ll repairs should be made by
an authorized service workshop. Improper charger assembly may
cause electric shock or fire.
• Disconnect the charger from power supply before starting any
maintenance or cleaning.
• When the charger is not in use, it should be disconnected from
the power network.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of injuries at work.
Li-ion batteries may leak, set on fire or explode when heated to
high temperature or short-circuited. Do not store the batteries
in a car in hot and sunny days. Do not open the battery. Li-ion
batteries contain electronic protection devices that, if damaged,
may cause fire or explosion of the battery.
CONSTRUCTION AND USE
Drill is a battery powered tool. Drive consists of a D C commutator
motor with permanent magnets and planetary gear. Drill is designed
for screwing in and out screws and bolts in wood, metal, plastics and
ceramics, and for drilling holes in these materials.
C ordless, battery-
powered power tools are especially useful for works in interior
furnishing, adaptation of premises etc.
Use the power tool according to the manufacturer’s instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Quick-release chuck
2. Torque adjustment ring
3. Direction selector switch
4. Socket for charger
5. Switch
6. Lighting
7. C harger
8. L E D
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CA UTION
W A RNING
A SS E MBLY / S E TTINGS
INFORM A TION
EQUIPMENT AND ACCESSORIES
1. C harger - 1 pce
PREPARATION FOR OPERATION
BATTERY CHARGING
Drill is supplied with partially charged battery. C harge the battery
when ambient temperature is within range 4° C – 40° C . Battery that
has not been used for a long time will reach full efficiency after
approximately
3 to 5 charge/discharge cycles.