VersaLogic Owl Hardware Reference Manual Download Page 68

Page: 68 / 71

Thermal Considerations

VL-EPU-4012 Hardware Reference Manual

Heat Plate Up

Use this assembly method if you are adding a heatsink to the standard Owl heat plate. Figure 37
(a representative image of a similar VersaLogic product) shows an EPU assembly including the
optional heatsink.

Figure 37. An Example of Hardware Assembly with Heat Plate Up

The recommended assembly method for this configuration is as follows:

Attach the heatsink to the Owl heat plate.

Attach the baseboard to the enclosure with standoffs.

Installing the VL-HDW-416 Passive Heat Sink

Apply the Arctic Silver

Thermal Compound (VL-HDW-401)



Apply the thermal compound to the heat plate using the method described on the Arctic
Silver website -

http://www.arcticsilver.com/

Position the passive heat sink



Using Figure 38 as a guide, align the five mounting holes of the heat sink with the heat
plate.



Orient the heat sink fins in the direction of the system airflow to maximize CPU cooling.

Secure the passive heat sink to the heat plate



Affix the passive heat sink to the heat plate using five M2.5 pan head screws.



Using a torque screwdriver, tighten the screws to 4.0 inch-pounds.

Summary of Contents for Owl








































































Search results

Summary of Contents for Owl

Reviews:

Related manuals for Owl

Brands by name

Popular brands

VersaLogic Owl, Hardware Reference Manual

Search results

Summary of Contents for Owl

Reviews:

Related manuals for Owl

Brands by name

Popular brands