manualshive.com logo in svg

VersaLogic Owl, Hardware Reference Manual

Share
Download
VersaLogic Owl Hardware Reference Manual Download Page 16

Board Features 

VL-EPU-4012 Hardware Reference Manual  

16 

 

 

3. Review Configuration 

 

Before you power up the system, double-check all the connections. Make sure all cables are 
oriented correctly, that adequate power is supplied to the Owl and all attached peripheral 
devices. 

4. Power On 

 

Turn on the ATX power supply and the video monitor. If the system is correctly configured, 
a video signal should be present.  

5. Install Operating System 

 

Install the operating system according to the instructions provided by the operating system 
manufacturer. 

BIOS Setup 

The Owl permits the storage of user-defined BIOS settings. This enables you to retrieve those 
settings from cleared or corrupted CMOS RAM, or battery failure. All BIOS defaults can be 
changed, except the time and date. BIOS defaults are updated using the BIOS Update Utility. 
 

CAUTION

: If BIOS default settings make the system unbootable and prevent the user from 

entering the BIOS Setup utility, the Owl must be serviced by the factory. 

Default BIOS Setup Values 

After CMOS RAM clears, the system loads default BIOS parameters the next time the board 
boots. The default CMOS RAM setup values are used in order to boot the system whenever the 
main CMOS RAM values are blank, or when the system battery is dead or has been removed 
from the board. 

Operating System Installation 

The standard PC architecture used on the Owl makes the installation and use of most of the 
standard x86-based operating systems very simple. 

 

Summary of Contents for Owl








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands