manualshive.com logo in svg

VersaLogic Owl, Hardware Reference Manual

Share
Download
VersaLogic Owl Hardware Reference Manual Download Page 24

Board Features 

VL-EPU-4012 Hardware Reference Manual  

24 

 

 

Cabling 

If your application requires a custom cable, the following information will be useful: 

VL-EPU-4012 Board Connector 

Mating Connector 

Molex 501331-0207 

Molex 501330-0200 

VL-CBR-0203 External Battery Module 

The VL-CBR-0203 external battery module is compatible with the Owl. For more information, 
contact 

[email protected]

. 

Figure 9. VL-CBR-0203 Latching Battery Module 

 

External Speaker 

The User I/O connector (shown in Figure 19 on page 36) includes a speaker output signal at pin 
15. The VL-CBR-4005B paddleboard provides a piezoelectric speaker. Figure 28 on page 54 
shows the location of the piezoelectric speaker on the VL-CBR-4005B paddleboard. 

Push-button Reset 

The User I/O connector (shown in Figure 19 on page 36) includes an input for a push-button 
reset switch. Shorting pin 18 to ground causes the Owl to reboot. This must be a mechanical 
switch or an open-collector or open-drain active switch with less than a 0.5V low-level input 
when the current is 1 mA. There must be no pull-up resistor on this signal. This connector uses 
IEC 61000-4-2-rated TVS components to help protect against ESD damage. 

A reset button on the VL-CBR-4005B paddleboard is provided. Refer to the chapter titled VL-
CBR-4005B Paddleboard, beginning on page 54 for more information. 

Summary of Contents for Owl








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands