Versalift VST-8000-I, Operator'S Manual

Page: 21 / 64

3-3
39026-03 02/17 VERSALIFT VST-8000/8500/9000/9500-I
SPECIFICA
TIONS
RADIAL OUTRIGGERS - Radial outriggers are
designed and constructed from high-strength steel.
At 11 in. (0.28 m) of penetration the outriggers provide
211 in. (5.36 m) of spread based on a 40 in. (1.02
m) frame height. Outriggers are equipped complete
with pilot operated check valves, internal thermal
relief valves, and separate operating controls for
each outrigger.
OUT AND DOWN OUTRIGGERS – Out and down
outriggers are designed and constructed from
high-strength steel and provide 8 in. (200 mm) of
penetration and 195 in. (5.0 m) of spread based
on a 40 in. (1.02 m) frame height. Outriggers are
equipped complete with pilot operated check valves,
internal thermal relief valves, and separate operating
controls for each outrigger.
SUBFRAME – The full-length subframe is constructed
of 6 x 8 tubing. Shear plates are provided to attach
to the chassis frame.
BACKUP PUMP - The backup pump is driven by
a DC motor, which is powered by the truck-engine
battery. The system is connected in parallel with
the main pump and is designed for non-continuous
operation. An air cylinder at the upper controls and
a toggle switch at the turret are used to energize
the system.
SECOND SET OF TOOL POWER PORTS - A second
set of tool power ports are installed at the platform to
accommodate a second open center tool.
TOOL POWER AT THE GROUND CONTROLS -
The hydraulic tools must be open-center. The tool
circuit provides approximately 6 gpm at engine idle
and 10 gpm with the throttle control engaged. The
tool pressure is 2000 psi (140 Bars)
EXTRA CONTROL CIRCUIT - Consists of an
additional air cylinder at the platform, toggle switch at
the pedestal, pressure switch in the turret and airline
to the platform. An additional pass in the collector
ring is required for each control circuit.
CATEGORY B DIELECTRIC TESTING AND
CERTIFICATION
- Testing and certifi cation for
ANSI A92.2 Category B 46 KV and below or 69 KV
is available. Aerial devices may be designed and
confi gured for gloving work provided it meets the
requirements per ANSI A92.2 Category B. The test
system includes interior and exterior test bands and
bonding of all interior boom parts at the elbow end
of the upper boom. The components are wired to a
single external plug. This option includes vacuum
prevention for all the hydraulic hoses routed through
the insulated booms.
COMPONENTS TO ALLOW CATEGORY A
CERTIFICATION
– Consists of interior and exterior
test bands, test band shields, corona ring, sealed
inner boom, aluminum platform liner, and bonding
of boom tip components. This option allows the
customer to certify unit up to 345 kv per ANSI A92.2
Category A (138 kv for VST-9500-I only). Aerial
devices may be designed and confi gured for gloving
work provided it meets the requirements per ANSI
A92.2 Category A. The certifi cation test is to be
provided by the customer after delivery. This option
includes vacuum prevention for all the hydraulic
hoses routed through the insulated booms.
CATEGORY D DIELECTRIC TESTING AND
CERTIFICATION
- Testing and certifi cation for
ANSI A92.2 Category D are available. These aerial
devices which are designed and manufactured for
work in which the insulating system is not considered
as primary insulation, but secondary. These aerial
devices are NOT designed for gloving work methods.
They are rated at voltages of 46kv.
INNER BOOM COVER – A vinyl cover is available
for the fi berglass inner boom.
PLATFORM VARIATIONS:
24 in. x 30 in. (0.61 m x 0.76 m) Closed Fiberglass
Platform
24 in. x 42 in. (0.61 m x 1.07 m) Closed Fiberglass
Platform
PLATFORM COVER - Vinyl covers are available for
the platforms.
PLATFORM LINER - Platform liners are available
for each of the closed platforms.
LIFTING EYE - A lifting eye attachment near the
knuckle end of the lower boom/compensation link
has a 1500 lbs. (680 kg) maximum capacity.
1000 LBS MANUAL JIB AND WINCH - The material
handling jib and winch consists of a winch and a jib
pole that are automatically leveled with the platform.
This jib provides 250 to 1000 lbs. jib capacity
depending on the boom positions.
THE UPPER CONTROLS DO NOT PROVIDE
PROTECTION IN THE EVENT OF ELECTRICAL
CONTACT AND ARE NOT A SUBSTITUTE FOR
MINIMUM APPROACH DISTANCES, COVER-UPS,
RUBBER GLOVES AND OTHER PERSONAL
PROTECTIVE EQUIPMENT.