background image

11

BFC36 Balance Flue Heat-Circulating Fireplace

7412647

Installing the 

Chimney System

Start by attaching the first chimney section to the collar 
on top of the fireplace.

  

Install the pipe as pictured in Figure 14.  When  you 
get a good lock, you will hear the pipe clearly snap 
together. Once sections are snap-locked in place, it is 
extremely difficult to get them apart. 

Make sure the 

pipe is firmly snapped and locked together as each 
pipe section is mounted.

When installing elbows, only outer pipe will snap- 
lock.  Middle pipes simply slide into position. Be sure 
to always attach straps on upper elbow to a structural 
framing member. (Fig. 15)
Continue installing the pipe as required until pipe is 
installed up through the ceiling.  At this point, you must 
install a firestop spacer.

Installing the Firestop Spacer 

in the Ceiling Hole

A firestop spacer is used to keep pipe spaced properly 
and required for safety.
Nail the firestop spacer (at each corner) to the framing 
members of the ceiling hole. 

NOTE: 

 A firestop spacer 

is not required at the roof.
Hole sizes listed in Figure 11 for angled firestop spac-
ers provide minimum required air space to chimney 
pipe for ceiling thickness up to 8” (203mm).  When 
combined thickness of ceiling material, ceiling joists 
and flooring material exceeds 8” (203mm), adjustments 
must be made in framing to assure that minimum air 
spaces to chimney are maintained.

Proper Firestop Spacer Installation

Figure 16 shows different installation procedures for  
both an area that 

is

 an attic 

and  an area that 

is not

 an 

attic.
If the area above the ceil-
ing

 is not 

an attic, position 

the firestop spacer with the 
flange on the ceiling side 
and the angled portion ex-
tending up into the hole.
If the area above the ceiling 

is

 an attic, position the fire-

stop spacer with the flange 
on the top of the framed 
hole and the angled portion 
extending down into the 
hole.

UP

FPC558a

BFC

Pipe install

Circulating models

8/21/00   djt

Pipe Section

Pipe 

Rim

Hem

Lance

Pipe 

Hem

FPC558a

Fig. 14

  Install pipe, listening for the snap-lock to fasten.

FP270/271

CR Series

2/19/99   djt

Support Structure

Ceiling 

Hole Fram-

ing

Elbow Strap

(must be tight)

Angled Firestop

Chimney Support Strap

(must be tight)

Elbow Strap

Angled Strap

FP270/271

Fig. 15

  Attach straps to a structural framing member.

FP593

SR/C

11/20/97

Nails (4)

F

irestop 

Spacer

Joist

F

irestop 

Spacer

Nails (4)

Joist

Attic Installation

 

Ceiling Installation

FP593

Fig. 16

  Installing firestop spacer.

Summary of Contents for 647 BFC

























Reviews: