Veris Industries E31A002 Installation Manual Download Page 17 | Manualshive

Page: 17 / 26

Veris Industries E31A002 Installation Manual Download Page 17

Z206855-0B

Page 17 of 26

©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 04142

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Installation Guide

Power Monitoring

E31E Series

TM

2. Set the IP address for use on the BACnet/IP network:

a. From the navigation tree (left column) on the GUI, click on Setup and then Network Settings to enter the Edit IP Address
Settings menu.

b. Enter the desired IP address in the N1_IP_Address field (in the format xxx.xxx.xxx.xxx)

c. If necessary, change the Subnet Mask by entering the appropriate new value in the N1_Netmask field

d. If the E31E is connected to an ethernet gateway, enter its IP address in the Default Gateway field. This is especially critical if
the E31E will be used as a BACnet BBMD device.

e. Click the Update IP settings button. The E31E changes its settings and restarts. The GUI does not connect again until the E31E
is installed on the network that matches those settings and the new IP address is entered into a web browser on a PC properly
configured for that network.

Gateway
Configuration (cont.)

Shop for Power Metering products online at:

1.888.610.7664

www.

PowerMeterStore

.com

«
...
15
16
17
18
19
...
»

Summary of Contents for E31A002



























Reviews:

No comments