manualshive.com logo in svg

Veris Industries E31A002, Installation Manual, Page: 15 / 26

Share
Download
Veris Industries E31A002 Installation Manual Download Page 15

Z206855-0B 

Page 15 of 26 

©2014 Veris Industries   USA 800.354.8556 or +1.503.598.4564  / [email protected] 04142 

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of  Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Installation Guide

Power Monitoring

E31E Series

TM

d. Highlight Internet Protocol Version 4 (TCP/IPv4), and click OK.

e. Select <Use the following IP Address>. Make note of the IP address that appears, then enter the static IP address (e.g. if the 
E31E Series is still set to its default address of 192.168.1.24, then change it to 192.168.1.100). Enter for the 255.255.255.0 subnet 
mask. Click OK.

 

Enter static 

IP address

Enter subnet 

mask

e.  Click Close.

3.  Open a PC web browser and enter the IP address of the E31E (default address is 192.168.1.24) to access the GUI. The GUI launches 

and appears in the browser window.

4.  When finished using the GUI, unplug the ethernet cable from the PC and restore the IP settings as needed.

Gateway 
Configuration (cont.)

Shop for Power Metering products online at:

1.888.610.7664

www.

PowerMeterStore

.com

Summary of Contents for E31A002



























Reviews:

No comments