background image

17

18

Caution

U.S. Federal Law restricts this device to sale by or

on the order of a physician or licensed

practitioner. 

Caution

To ensure proper interpretation of VeriChip H2

Reader output, perform display check on unit

prior to use. 

Caution

Do not expose VeriChip H2 Reader to excess

moisture or electrostatic discharge.

Caution

If VeriChip H2 Reader is dropped, perform display

check through a power-up cycle (see Reader

Activation) and read functionality check using the

test Microtransponder.

Caution

Not MRI Compatible

. Do not attempt to use the

VeriChip H2 Reader to read a Microtransponder

while patient is exposed to active MRI equipment.

The VeriChip H2 Reader is a Radio

Frequency (RF) device and needs

special precautions regarding

electromagnetic compatibility

(EMC), read these instructions for

EMC information before putting

the device into service.

Warning

:  VeriChip H2 Reader should not be used adjacent

to or stacked with other equipment.  If adjacent or

stacked use is necessary, the VeriChip H2 Reader

should be observed to verify normal operation in

the configuration in which it will be used.

Warning

The VeriChip H2 Reader generates, uses, and can

radiate radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to radio

communications.  Operation of this equipment in a

residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at personal

expense.

NOTES:

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

______________________________________________

Summary of Contents for VeriChip H2












Reviews: