VERDER Verderflex Vantage 5000 Series Original Operating Manual Download Page 32

Page: 32 / 58

Vantage 5000

1.4v-09.2019

32 | Page

7.7 Users / Passcodes

7.7.1 Users / Passcodes - an Overview

Access control is DISABLED by default. Access control can be used to restrict access to pump settings for different users. These

settings will not affect the START/STOP buttons.

There are 3 levels of access available on the pump:

•

ADMIN – allows access to every setting on the pump.

•

SUPERVISOR – allows access to limited settings only.

•

OPERATOR – allows read-only access to the pump settings.

Access Level

Admin

Supervisor

Operator

Permitted Settings

Full access:

• Home Screen Functionality

• Job Files Menu

• Calibration Menu

• Settings Menu

• Remote Control Menu

• Users/Passcodes Menu

• Logs/History Menu

Full access:

• Home Screen Functionality

• Job Files Menu (edit job

files and delivery setup, without

operational mode)

• Calibration Menu

• Logs/History Menu

Read-only access:

• Home Screen

• Log/History Menu

Restricted Settings

N/A

• Cannot access Settings

• Cannot access Remote

Control Menu

• Cannot access Users/

Passcodes Menu

• Cannot access Job Files

• Cannot access Calibration

• Cannot access Settings

• Cannot access Users/

Passcodes Menu

• Cannot access Remote

Control Menu

• Cannot export Logs/History

Table 8 Access Levels

Summary of Contents for Verderflex Vantage 5000 Series



























































Search results

Summary of Contents for Verderflex Vantage 5000 Series

Reviews:

Related manuals for Verderflex Vantage 5000 Series

Brands by name

Popular brands

VERDER Verderflex Vantage 5000 Series, Original Operating Manual

Search results

Summary of Contents for Verderflex Vantage 5000 Series

Reviews:

Related manuals for Verderflex Vantage 5000 Series

Brands by name

Popular brands