VERDER VERDERAIR VA 25 Repair Parts Download | Manualshive

Page: 10 / 35

background image

10

859.0089

Replace Seals or Rebuild Air Valve

NOTE: Repair kits are available. See page 25 to order
the correct kit(s) for your pump. Air Valve Seal Kit parts
are marked with a †. Air Valve Repair Kit parts are
marked with a



. Air Valve End Cap Kit parts are

marked with a



.

Disassemble the Air Valve

1.

Perform steps 1-5 under Replace Complete Air
Valve, page 9.

2.

See F

IG

. 3. Use a Torx screwdriver (T8 for alumi-

num centers, T9 for plastic centers) to remove two
screws (209). Remove the valve plate (205),
cup assembly (212-214), spring (211), and detent
assembly (203).

3.

Pull the cup (213) off of the base (212). Remove the
o-ring (214) from the cup.

4.

See F

IG

. 3. Remove the retaining ring (210) from

each end of the air valve. Use the piston (202) to
push the end caps (207, 217) out of the ends.
Remove end cap o-rings (206).

5.

Remove the u-cup seals (208) from each end of the
piston (202), then remove the piston. Remove the
detent cam (204) from the air valve housing (201).

Reassemble the Air Valve

NOTE: Apply lithium-based grease whenever instructed
to grease. Order Verder part number 819.0184.

1.

Use all parts in the repair kits. Clean other parts and
inspect for damage. Replace as needed.

2.

Grease the detent cam (204) and install into hous-
ing (201).

3.

Grease the u-cups (208) and install on the piston
with lips facing toward the center of the piston.

4.

Grease both ends of the piston (202) and install it in
the housing (201), with the flat side toward the cup
(212). Be careful not to tear u-cups (208) when slid-
ing piston into housing.

5.

Grease new o-rings (206) and install on the end
caps (207). Install the end caps into the housing.

6.

Install a retaining ring (210) on each end to hold end
caps in place.

F

IG

. 2. Air valve u-cup installation

Lips face down

Lips face up

208



†

208



†

202



ti12754a

«
...
8
9
10
11
12
...
»

Summary of Contents for VERDERAIR VA 25




































Reviews:

No comments

Related manuals for VERDERAIR VA 25

Brand: YAMADA Pages: 14

Brand: SereneLife Pages: 10

TURBOPOWER 1000 P 225A-TPL

Brand: PVI Industries Pages: 1

Leslie F-1240LDW

Brand: Circor Pages: 19

Fairbanks nijhuis 2800

Brand: Pentair Pages: 28

Brand: Energie Pages: 31

HYDRA-SPRAY President A Series

Brand: Graco Pages: 20

Aqua-Pure 3MFF100

Brand: 3M Pages: 8

Brand: BLACKMER Pages: 14

Brand: Wacker Neuson Pages: 50

Brand: Flo Fab Pages: 9

Brand: Jandy Pages: 96

Brand: Barnes Pages: 26

Krystal Clear SF10220

Brand: Intex Pages: 27

SiFire EN 100/200-205-45 E

Brand: Wilo Pages: 108

Brand: Waterhouse Pages: 4

Brand: Clarke Pages: 12

Brand: Zodiac Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands