background image

www.ventilation-system.com

4

Do not touch the unit controls with wet hands.

Do not carry out the unit maintenance with wet 

hands.

Do not wash the unit with water.

Protect the unit electric parts from water ingress.

Use the unit only as intended by the manufac-

turer.

Do not connect a clothes dryer or other similar 

equipment to the unit or the ventilation system.

Do not put any water containers on the unit, i.e. 

flower vases.

Do not sit on the unit and do not put any objects 

on it.

OFF

ON

Disconnect the unit from power supply prior to 

maintenance.

Do not let children operate the unit.

Do not damage the power cable while operating 

the unit.

Do not put any objects on the power cable.

Keep combustible gases and inflammable prod-

ucts away from the unit.

Do not open the operating unit.

In case of unusual sounds, smell of smoke discon-

nect the unit from power supply and contact the 

service centre.

During a long-term operation of the unit periodi-

cally check the mounting for reliability.

Do not block the air duct when the unit is on.

Do not let air flow from the unit be directed to the 

open flame devices or candles.

UNIT OPERATION SAFETY PRECAUTIONS

Summary of Contents for VUT 1000 PW EC






















Reviews: