background image

Service information 

 

Service and maintenance must only be carried out by an authorised person

.

 

This appliance sh

ould

 not be modified. 

Always disconnect the gas supply and power before servicing the cooker. 
After service always check connections for gas soundness

.

NEVER

 use a naked flame to check for leaks. 

 

To remove the upstand (for cookers fitted with upstand)

.

 

1.  Pull 

the 

cooker forward

.

 

2.  To remove the upstand retaining brackets undo the 2 top and 2 rear retaining 

screws securing each bracket. 

3.  Lift the upstand from the cooker hob. 

 

To clean or replace a cooktop burner injector

.

 

1.  Remove 

the 

pan support, burner cap and burner head. 

2.  Using a 7mm socket spanner unscrew and clean or replace the cooktop burner's 

injector. 

3.  Replace burner head, cap and pan support. Ensure that the burner head and cap are 

in the correct position. 

 

To 

cl

ean or replace the oven burner or in

j

ector

.

 

1.  Drop down or remove the oven door.  
2.  Remove left hand side panel as per the headings 'To remove side panels'. 

3. 

The oven burner is held in position over the injector by a 

bracket on the 

LHS 

retaining the elbow of the burner mixing 

tube 

and a retention bracket on the 

RHS 

at the end of the 

burner. Using a 

P

hillips head screw driver unscrew the single 

screws securing the burner on either side to the brackets and remove the burner 
being careful not to strain the thermocouple and electronic ignition leads.

 

4. 

Using a 7mm socket spanner unscrew and clean or replace the oven burner 
injector. If replacing the actual burner, first remove the spring clips to release the 
thermocouple and the electronic spark ignitor.

 

5. 

Reassemble in reverse order.

 

 

 

 

Access to the under hob area 

Pull 

the 

cooker forwards to gain access to the rear of the cooker 

1. Remove upstand 
2.  Remove pan supports, burner caps and burner heads 
3.  Using a torx T20 head driver remove the screws securing the burners to the hob. 2 per 

boiling burner and 4 for the wok burner. 

4.  Remove the lower 2 screws of each upstand bracket 
5. 

 L

ift hob at 

the 

rear and slide 

it 

out of position. 

 
 

 
 
 
 

Summary of Contents for VEF91GG






















Reviews: