background image

ii

TABLE OF CONTENTS

INTRODUCTION .......................................... 1
SPECIFICATIONS........................................ 2

Cabinet Inches Metric............................... 2
Glass ......................................................... 2
Electrical.................................................... 2
Capacity .................................................... 2
Pricing ....................................................... 2

UNPACKING & INSTALLATION ................. 2
GROUNDING & ELECTRICAL .................... 3
LOADING PRODUCTS ................................ 3
CHANGING TRAY CONFIGURATION
AND RETIMING............................................ 4

Removing and Replacing Trays ................ 4
Changing Timing ....................................... 4

Product pushers..................................... 4
Retiming GF12 II.................................... 5
Retiming GF19 II and GF35 II................ 5

Changing Tray Configuration .................... 5

GF12 II................................................... 5
GF19 II and GF35 II............................... 5

CONTROLLER FUNCTIONS ....................... 6

Sales Mode ............................................... 6
Service Mode ............................................ 7

Displayed Errors.....................................7
Programming the Controller ...................8

COIN MECHANISM ....................................11

Option Switch Setting...............................11

DOLLAR BILL VALIDATOR.......................12

Removing Accepted Bills .........................13
Troubleshooting .......................................14
Clearing Jams and Cleaning....................14

CARE & CLEANING ...................................14

Cabinet Interior ........................................14
Cabinet Exterior .......................................14

PARTS ORDERING ....................................15

Trays........................................................15
Augers .....................................................15
Procedure ................................................15

To Order by Mail...................................15
To Order by Fax ...................................15
To Order by Phone...............................15

SCHEMATIC – GF12 II ...............................16
SCHEMATIC – GF19 II ...............................17
SCHEMATIC – GF35 II ...............................18

Record the Model Number and Serial Number of your machine below.
The Model and Serial numbers are needed for quick service and parts information for your machine.
The numbers are available on the identification plate located on the back of the cabinet of the machine.

MODEL NUMBER:

 __________________________________________________

SERIAL NUMBER:

 __________________________________________________

Summary of Contents for 3120-GF12 II





















Reviews: