background image

Fume Exhaust Fans

17

Parts List

CAUTION

A fan manufactured with an explosion resistant motor 
does not certify the entire unit to be explosion proof. 
Refer to UL Listing Mark for the fans approved usage.

Each fan bears a manufacturer’s nameplate with model number and serial number embossed. This information will 
assist the local Venco representative and the factory in providing service and replacement parts. Before taking any 
corrective action, make certain unit is not capable of operation during repairs.

CAUTION

La présence d’un moteur antidéflagrant sur un 
ventilateur ne garantit pas que tout l’appareil est 
antidéflagrant. Pour connaître les emplois autorisés 
de l’appareil, voir son marquage de conformité UL.

VJC-315 Belt Drive

Shown with optional accessories, 
spring isolators and equipment 
supports.

Stack

Weatherhood
Components

Motor Pulley 
(driver)

Shaft Pulley 
(driven)

Drive Side 
Bearing

Opposite 
Drive Side 
Bearing

Fan Shaft

Heat Slinger

Rub Ring

Shaft Seal

Motor

Restrained Spring Isolators

Equipment Supports

Scroll Housing

Inlet Cone

Inlet Flange

Inlet 
Companion 
Flange

Wheel

Belt(s)

Summary of Contents for VJC-200





















Reviews: