Veko Joris Manual Download Page 16

General disclaimers

IP65

Product specifications

- Ambient working range

-25 °C-+35 °C (-13 °F - 95 ° F)

- Storage

-25 °C-+35 °C (-13 °F - 95 ° F)

- Rated voltage range

220 V~-240 V~ 50/60 Hz   

- Relative humidity

10 %-85 % RH - not condensing

- Cable specification

7&3 pin suitable for solid wiring (Ø1.5-2.5 mm2)  

Important

- Caution, risk of electric shock!

- Hot plug-in is not an option and may cause damage to the luminaire.

- Disconnect the mains before installing or modifying this product.

- Installation and commissioning of the luminaire must be performed by a qualified electrician in accordance with

all national and/or local regulations.

- Install all individual light lines before connecting to the grid.

- NEVER install this product without reading this installation guide.

- NEVER stare into this product when switched on.

- NEVER modify or alter this product, this will result in loss of warranty.

- Read the product labels carefully for all product details.

- This product is not suitable for signal functions, in case of emergency function see next paragraph.

- This product is not suitable for outdoor use.

- This product is not suitable for off-grid power solutions.

- On this product no condensation allowed during storage, operation and application.

- When operating the electrical connections and connecting to the mains or grid always work according to standard

NEN 1010 and NEN 3140.

Note

- A Veko linear lighting system is considered as a single luminaire (a 'closed' system) and not an electrical installation

at itself.

- The light source of this product is custom made and shall only be replaced by the manufacturer or his service agent.

- At end of life, the whole product needs to be replaced.

- This product is not intended for household usage.

- Take care with the usage of power cables and prevent damage to the cables when installing them.

- Avoid touching the product if active, it might cause harm due to heat

- When the product is unpacked, take care of placement. Do not let the product rest on top of the optics,

damage to optics will result in light output loss.

- The manufacturer is not liable for damages resulting from improper of faulty installation or operation from

unauthorized modifications to the luminaire.

- Specifications are subject to change without notice! If you have questions please contact the manufacturer.

- Take appropriate precautions: wear gloves.

When adjusting the length of the light lines between the walls, an expansion coefficient of 24x10 -6 (2.4 mm per 100 m

per °C) should be taken into account.

- Keep at least one copy of this document as future reference material.

Cleaning

 

- ALWAYS switch off the power to the product before cleaning.

- This product can be cleaned with a damp cloth.

- Choose cleaning materials which are suitable for plastic.

- Do not use coarse or rough cleaning tools on this product.

- Do not use bleach or solvents on this product.

- Do not use any type of high pressure equipment to clean this product.

- Do not submerge this product.

16/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / General disclaimers

Summary of Contents for Joris

















Reviews: