Veichi VH600 Manual Download Page 3

    -2-     

 

the product, or there are missing or damaged parts. 

 

Please check the packing list carefully. please do not install them if they don’t match the 
packing list. 

Note

 

 

Before unpacking, please check whether the outer packaging of the equipment is in good 
condition, whether it is damaged, soaked, damp or deformed. 

 

Please open the package from outside to inside. Do not pound on it! 

 

When  unpacking,  please  check  the  surface  of  equipment  and  accessories  for  damage, 
corrosion, bruise, etc. 

 

After unpacking, please carefully check quantity and names of the products against the list 
and check if any files or manuals are missing. 

Storage & Transportation 

Note

 

 

When handling products, please lift them lightly, and pay attention to the objects under your 
feet at any time to prevent tripping or falling, otherwise it may cause personal injuries or 
product damages. 

 

When handling products with bare hands, please hold on to the product housing to avoid 
falling, otherwise it may cause personal injuries. 

 

Please strictly follow the required storage and transportation requirements for storage and 
transportation, otherwise it may cause product damages. 

 

Avoid  storage  and  transportation  under  water  splashing  and  rain,  direct  sunlight,  strong 
electric field, strong magnetic field and strong vibration. 

 

Avoid storing products for more than 3 months. And please carry out stricter protection and 
necessary inspections if it is longer than 3 months. 

 

Please pack the products carefully before transporting them by vehicles. Sealed boxes must 
be used for long-distance transportation. 

 

Do not transport this product together with equipment or articles that may affect or damage 
this product. 

Installation 

Danger

 

 

Only professionals with relevant training in electrical equipment and electrical knowledge 
can carry out operation on this product. Please keep non-professional personnels away from 
this product. 

Warning

 

 

Please read the product manual and safety precautions carefully before installation! 

 

Please do not install this product in places with strong electric field or strong electromagnetic 
wave interference. 

 

Before carrying out installation, ensure that the installation position is sufficient to support 
the weight of the equipment. 

 

Do not wear loose clothes or accessories when installing, otherwise you may get an electric 

Summary of Contents for VH600






























Reviews: