background image

5

1 For your safety

VEGAPULS SR 68 • Modbus and Levelmaster protocol

47164-EN-180226

This device complies with Part 15 of the FCC Rules. Operation is 

subject to the following two conditions:

• 

This device may not cause interference, and

• 

This device must accept any interference, including interference 

that may cause undesired operation of the device

This device is approved for unrestricted use only inside closed, sta

-

tionary vessels made of metal, reinforced fiberglass or concrete.
Changes or modifications not expressly approved by the manufac

-

turer could void the user’s authority to operate this equipment.

1.9  Environmental instructions

Protection of the environment is one of our most important duties. 

That is why we have introduced an environment management system 

with the goal of continuously improving company environmental pro-

tection. The environment management system is certified according 

to DIN EN ISO 14001.

Please help us fulfil this obligation by observing the environmental 

instructions in this manual:

• 

Chapter "

Packaging, transport and storage

"

• 

Chapter "

Disposal

"

Summary of Contents for VEGAPULS SR 68

























Reviews: