background image

4

1 For your safety

VEGAPULS 68 • 4 … 20 mA/HART - four-wire

51905-EN-180222

During the entire duration of use, the user is obliged to determine the 

compliance of the necessary occupational safety measures with the 

current valid rules and regulations and also take note of new regula-

tions.
To avoid any danger, the safety approval markings and safety tips on 

the device must also be observed and their meaning looked up in this 

operating instructions manual.

1.5  Safety label on the instrument

The safety approval markings and safety tips on the device must be 

observed.

1.6  EU conformity

The device fulfils the legal requirements of the applicable EU direc-

tives. By affixing the CE marking, we confirm the conformity of the 

instrument with these directives.
You can find the EU conformity declaration on our website under 

www.vega.com/downloads.

Electromagnetic compatibility

The instruments are designed for use in an industrial environment. 

Nevertheless, electromagnetic interference from electrical conductors 

and radiated emissions must be taken into account, as is usual with a 

class A instrument according to EN 61326-1. If the instrument is used 

in a different environment, its electromagnetic compatibility with other 

devices must be ensured by suitable measures.

1.7  Fulfillment of NAMUR recommendations

NAMUR is the automation technology user association in the process 

industry in Germany. The published NAMUR recommendations are 

accepted as the standard in field instrumentation.
The device fulfils the requirements of the following NAMUR recom-

mendations:

• 

NE 21 – Electromagnetic compatibility of equipment

• 

NE 43 – Signal level for fault information from measuring transduc-

ers

• 

NE 53 – Compatibility of field devices and display/adjustment 

components

For further information see www.namur.de.

1.8  Radio license for Europe

The instrument was tested according to the latest issue of the follow-

ing harmonized standards:

• 

EN 302372 - Tank Level Probing Radar

It is hence approved for use inside closed vessels in countries of the 

EU.
Use is also approved in EFTA countries, provided the respective 

standards have been implemented.

Summary of Contents for VEGAPULS 68





















Reviews: