Vega VEGAMET 861 Operating Instructions Manual Download Page 52

Page: 52 / 72

12 Diagnostics and servicing

VEGAMET 861 • 4 … 20 mA/HART

58866-EN-200401

incorrect parameter adjustment, a fault signal is triggered. In case of

an instrument defect or line break/shortcircuit, a fault signal is also

triggered.
The fault indication lights up in case of failure and the current output

as well as the relays react according to the configured fault mode. If

the fail safe relay was configured, it will deenergize. In addition, one

of the following error messages is outputted on the display and the

background lighting changes to colour acc. to NAMUR NE 107.

Error code

Cause

Rectification

F002
Measuring point

not configured

Measuring point

was not yet con-

figured

No sensor assigned.

For measuring point 3: No application

with 3 measuring points was selected.

F003
Hardware: CRC

error

CRC error (error

with self-check)

Switch the instrument off/on

Carry out a reset

Send instrument for repair

F008
Sensor input:
Failure, sensor

Sensor not found Check connection of the sensor

Check HART address of the sensor

F012
Hardware: AD

converter

Hardware error,

sensor input

Switch the instrument off and on

Send instrument for repair

F013
Sensor input:
Sensor error

The input of the

measuring point

returns an error
The connected

sensor returns

an error

Switch device/sensor off an on

Send device/sensor for repair

F014
Sensor input:

Short-circuit

Sensor cur-

rent > 21 mA or

short-circuit

Check sensor, e.g. on failure

Remove short-circuit

F015
Sensor input:

Line break

Sensor in boot

phase
Sensor current

< 3.6 mA or line

break

Check sensor, e.g. on failure

Remove line break

Check connection of the sensor

F034
EEPROM: CRC

error

EEPROM: CRC

error

Switch the instrument off and on

Carry out a reset

Send instrument for repair

F035
ROM defective

ROM: CRC error

Switch the instrument off and on

Carry out a reset

Send instrument for repair

F036
RAM

RAM error

Switch the instrument off and on

Carry out a reset

Send instrument for repair

F037
RAM

RAM defective

Switch the instrument off and on

Carry out a reset

Send instrument for repair

Failure

Summary of Contents for VEGAMET 861









































































Search results

Summary of Contents for VEGAMET 861

Reviews:

Related manuals for VEGAMET 861

Brands by name

Popular brands

Vega VEGAMET 861, Operating Instructions Manual

Search results

Summary of Contents for VEGAMET 861

Reviews:

Related manuals for VEGAMET 861

Brands by name

Popular brands