manualshive.com logo in svg

Vega VEGABAR 82, Operating Instructions Manual

Share
Download
Vega VEGABAR 82 Operating Instructions Manual Download Page 75

75

11 Supplement

VEGABAR 82 • Profibus PA

45031-EN-220624

Fig. 46: VEGABAR 82: Block diagram with AI FB 1 … AI FB 3 OUT values 

TB  Transducer Block

FB  Function Block

AI  Analogue Input

Module of the PA sensors

For the cyclic data traffic, VEGABAR 82 provides the following modules: 

• 

AI FB1 (OUT)

 

– Out value of the AI FB1 after scaling

• 

AI FB2 (OUT)

 

– Out value of the AI FB2 after scaling

• 

AI FB3 (OUT)

 

– Out value of the AI FB3 after scaling

• 

Free Place

 

– This module must be used if a value in the data telegram of the cyclical data traffic should not 

be used (e.g. replacement of temperature and Additional Cyclic Value)

A maximum of three modules can be active. By means of the configuration software of the Profibus 

master you can determine the configuration of the cyclical data telegram with these modules. The 

procedure depends on the respective configuration software.

Note:

The modules are available in two versions:

• 

Short for Profibus master supporting only one "Identifier Format" byte, e.g. Allen 

Bradley

• 

Long for Profibus master only supporting the "Identifier Format" byte, e.g. Siemens 

S7-300/400

Summary of Contents for VEGABAR 82

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands