background image

 

 

M-BUS-1 / User Manual 

 

16 

Revision 10 - 27 May 2019

 

4 VEGA LORAWAN CONFIGURATOR 

The  "Vega  LoRaWAN  Configurator"  application  (hereinafter  referred  to  as  the 

configurator) is intended for setting up the device via USB. 

The configurator has two modes of operation  - "Simple" and "Expert". In the "Simple" 

mode,  only  basic  settings  are  available.  In  the  "Expert"  mode,  the  basic  settings,  advanced 
settings and the ability to check the coverage area of the signal from the gateways are available. 
Next, the work of the application is considered in the 

Expert

 mode. 

INTERFACE OF THE APPLICATION 

The "Vega LoRaWAN Configurator" application does not require the special installation. 

When the executable file is launched, the window for working with the application appears. 

 

The menu on the left allows you to switch between the 

Simple

 and 

Expert

 modes, 

select the device model, connect to the device or disconnect from it, get and apply settings. 

The application window contains three tabs 

 Device info, LoRaWAN settings and device 

settings. 

The language selection menu is in the upper right corner. 

Summary of Contents for M-BUS-1





































Reviews: