background image

  

Installing The TLS-450PLUS Console

Connecting The Power Wires To The Console

8

Figure 4.  TLS-450PLUS Console - Fixed Comm Modules

Connecting The Power Wires To The Console

This section concludes the TLS-450PLUS retrofit installation by connecting power to the console. 

1. With the left of the console open, remove the two screws that attach the power connector cover plate (see 

Figure 2).

2. With the cover removed, notice the power connector already attached to the console. This is where the wires 

connect.

3. Next, remove the knockouts for console power and install the conduit from the power trough to the console. If 

local codes require rigid conduit, plan carefully before knocking out these holes. The console is prepunched for 
½” conduit. This should be large enough since the only wires going through this conduit will be for L1, neutral, 
panel ground and earth ground, and possibly 1 relay. Refer to manual 577014-073 for proper wire gauge.

Table 1. Selectable Comm Module Permissible Slots and Port Availability

Comm Module

Comm 

Type

Slot 1

Slot 2

Slot 3

Port Port 

Port 

1

2

1

2

1

2

R

S

-2

3

S

i

n

gle Port (al

s

o EDIM, 

S

atellite 

S

-

S

AT a

nd

 

S

atellite H-JBo

x

 a

pps

.)

S

erial

NC

C

NC

C

NC

C

R

S

-2

3

2 D

u

al Port (al

s

o EDIM, 

S

atellite 

S

-

S

AT a

nd

 

S

atellite H-JBo

x

 a

pps

.)

C

C

C

C

NC

C

R

S

-48

5

 

S

i

n

gle  Port

NC

C

NC

C

NC

C

R

S

-48

5

 D

u

al Port

C

C

C

C

NC

C

R

S

-2

3

2/R

S

-48

5

 D

u

al Port

C

(R

S

-2

3

2)

C

(R

S

-48

5

)

C

(R

S

-2

3

2)

C

(R

S

-48

5

)

NC

C

(R

S

-48

5

)

S

iteFa

x

 / Mo

d

e

m

NC

C

NC

C

NC

C

CDIM

DIM

C

NC

C

NC

----

----

USB ports: (1) upper, (2) lower

Future expansion port 

Ethernet ports:
(1) upper 

Ethernet port 2:
middle and lower switched 

Comm 

S

lot

s

Front of

Console

1

2

3

4

5

Summary of Contents for TLS-350l















Reviews: