background image

 

 

TLC3-FCR-2 Engineering Manual

 

 

Doc: 70-00-0202, V3.0 Date: 20111027 

© Vector Controls GmbH, Switzerland 

Page 1 

Subject to alteration 

TLC3-FCR-2  
Intelligent Fan Coil controller 

Features 

 

The PWM and 3-point floating control option reduces room 
temperature fluctuations and energy consumption 

 

Low power energy consumption: < 1W per unit 

 

Temperature control for 2- and 4-pipe fan coil systems.  

 

Automatic fan control for three stage fans.  

 

Cost saving option with Economy functionality and set point 
limitations 

 

Control for single stage heating, cooling and fan only 
operation modes 

 

Password protected programmable user and control 
parameters 

o

 

Setpoint range limitation 

o

 

Access control for setpoints, fan speeds and mode 
change 

o

 

Access control for heat/cool change and time 
programs 

o

 

Select your display contents 

o

 

Selectable behavior after return from power failure 

 

Temperature display in Celsius or Fahrenheit 

Deluxe Version: 

 

Clock and time schedule functions with power failure protection 

 

Blue backlight for LCD 

 

Infrared remote controller option:  
With special features for Boost and delayed switching on or off 

Applications 

 

Air Only Systems:  

o

 

Constant Air Volume systems with three stage fans for single or dual duct systems 

 

Air/Water Systems:  

o

 

Fan Coil units for 2-pipe or 4-pipe systems  

o

 

radiator control, chilled ceiling 

 

Simple individual room control for hotel rooms, meeting rooms, etc.  

 

PWM or On-Off-Control of 2 spring return valves or 3-point on-off or floating control of one 3-point valve.  

General Description 

The TLC3-FCR-2 is a stand-alone electronic fan coil controller with one control loop. The TLC3-FCR-2 features 1 NTC 
temperature sensor input and five binary outputs. Three outputs control a fan with low, medium and high fan speeds. 
Two binary outputs may be used to control either two spring return or thermal valves or one three point floating valve.  
A detailed parameterization is possible with the use of a simple configuration routine. The TLC3-FCR-2 can be 
configured using the standard operation terminal. No special tools or software is required.  

Ordering 

Item Name 

Item code 

Variant 

Power 

Features 

TLC3-FCR-2-24 
TLC3-FCR-2-24-W01 

40-10 0130 
40-10 0130-01 

Standard 
Cooling only 

24VAC/DC 

Fan coil controller with:  
1 TI int 
3 DO (Relay) Fan control 
2 DO (Relay) Binary valve control 

TLC3-FCR-2-D-24 
TLC3-FCR-2-D-24-W01 

40-10 0135 
40-10 0135-01 

Deluxe 
Cooling only 

TLC3-FCR-2-D-230 
TLC3-FCR-2-D-230-W01 

40-10 0119 
40-10 0119-01 

Deluxe 
Cooling only 

230VAC 

Fan coil controller with:  
1 TI int 
3 DO (Relay) Fan control 
2 DO (TRIAC) Binary valve control 

TLC3-FCR-2-230 
TLC3-FCR-2-230-W01 

40-10 0118 
40-10 0118-01 

Standard 
Cooling only 

Selection of valve actuators and fans 

Binary auxiliary devices: E.g. fans and on/off valves.  Observe switching power as detailed under technical 
specifications! Do not connect more than one fan coil unit to one controller. 

Summary of Contents for TLC3-FCR-2











Reviews: