background image

 

TCY-FT-U 

Operation Instructions 

 

Doc: 70-00-0128B, V1.2, 20110621 

© Vector Controls GmbH, Switzerland 

Page 4 

Subject to alteration 

Display and Operation 

 

Operation mode 

 

Comfort (occupied) 

All control functions operating per set points. 

 

Economy (unoccupied): 

Set points shifted according to 

Parameters CP04.

 

Economy mode and setpoint shift may be disabled with UP07 

OFF 

Energy Hold Off 

Outputs are off, inputs monitored for alarm condition 

 

Heating 

Output activates if temperature lower than setpoint 

 

Cooling 

Output activates if temperature higher than setpoint 

Power Failure 

All the parameters and set points are memorized and do not need to be reentered. Depending on 

UP05

 the unit will 

remain switched off, switch on automatically or return to the operation mode it was in before the power failure. 

Deluxe version only

: Timer operation and daytime setting will be retained for 24h. The controller has to be connected to a 

power supply for at least 10 hours for the backup function to operate accordingly.  

Error messages 

The TCY-FT-U may display the following error condition:  
 

Err1:

 

The connection to the temperature sensor may be interrupted or the temperature sensor is damaged.  
The output is switched off. Verify parameter settings and wiring.  

Left (POWER) 

Press < 2 sec.: Toggle STANDBY-
COMFORT mode or switch from OFF 

to ON 
Press > 2 sec.: Turn unit OFF. Text 
OFF displayed with current time 

(deluxe) temperature (standard) 
(Parameter setting: ENTER to 

select menu option, accept 
parameter change) 

Up  

Increment SET POINT  
(Parameter setting: 
SCROLL menu options 

and parameters) 

Down  

Decrement SET POINT  
(Parameter setting: SCROLL menu 

options and parameters) 

Mode 

Display of operation 

mode 

 

Large Digits 

Display of input or parameter 
value. 

Indicators 

1 Remote 

temperature sensor 

2 Dew point sensor 

Vertical Bar 

(scrolls up/down, 10% resolution) 

Small Digits 

Display of setpoint, clock or 
parameter number. 

 

Right (OPTION)  

Press < 2 sec.: Select Control Loop 

Press > 2 sec.: Manual H/C change 

(Parameter setting: ENTER to 
select menu option, accept 
parameter change) 
 

Summary of Contents for TCY-FT2-U-W01









Reviews: