Vector 40-300198, Manual

Page: 6 / 10

SRC-C1T1
CO2+T
EMPERATUR
T
RANSMITTER
/M
ONITOR
Doc: 70-00-0794A, V2.7, 20210310 © Vector Controls GmbH, Switzerland Page 6-10
Subject to change without notice www.vectorcontrols.com
Input configuration
Parameter Description Range Default
IP 00 TI1: Celsius or Fahrenheit, C = OFF, F = ON ON, OFF OFF
IP 01 TI1: Samples taken for averaging control signal 1) 1…255 10
IP 02 TI1: Calibration - 10…10 0
IP 03 TI1: Minimum temperature range
(temperature when output is at its minimum)
- 40…215 °C
- 40…4 19 °F
-40 °C
-40 °F
IP 04 TI1: Maximum temperature range
(temperature when output is at its maximum)
- 40…215 °C
- 40… 419 °F
60 °C
140 °F
IP 05 CI1: Light intensity of air quality LED on front 0…10 8
IP 06 CI1: Samples taken for averaging control signal 1) 1…255 10
IP 07 CI1: Calibration - 10…10% 0
IP 08 CI1: Minimum CO2 range ppm 2)
(CO2 level when output is at its minimum)
0…5000 ppm 0 ppm
IP 09 CI1: Maximum CO2 range ppm 2)
(CO2 level when output is at its maximum)
0…5000 ppm 2000 ppm
IP 10 CI1: CO2 level for medium CO2 indication 2) 0…5000 ppm 1000 ppm
IP 11 CI1: CO2 level for high CO2 indication 2) 0…5000 ppm 1600 ppm
IP 12 CI1: Enable ABC automatic CO2 background calibration ON, OFF ON
IP 13 CI1: Calibrate CO2 sensor
Note: For normal operation, calibration is not required. Only experts
should calibrate the sensor.
0 = No calibration (default)
1 = Calibrate to gas (0 ppm)
2 = Calibrate to fresh air (400 ppm)
0 … 2 0
1) Sample interval: 1 sec.
2) Changing this parameter affects the control of the air quality LEDs or relay as follows:
Air quality LED Use of Parameters
Green IP 08 value … ( IP 10 value + 400) / 2
Green + Orange ( IP 10 value + 400) / 2 … IP 10 value
Orange IP 10 value … ( IP 10 value + IP 11 value) / 2
Red ( IP 10 value + IP 11 value) / 2 … IP 11 value
Red IP 11 value … IP 09 value
Output configuration
Parameter Description Range Default
OP 00 AO1 (CO2): Configuration of CO2 output signal:
0 = CO2 value
1 = Recorded minimum CO2 value
2 = Recorded maximum CO2 value
0 … 2 0
OP 01 AO1 (CO2): Minimum limitation of CO2 output signal 3) 4) 0 …100 % 0 %
OP 02 AO1 (CO2): Maximum limitation of CO2 output signal 3) 4) 0… 100 % 100 %
OP 03 AO2 (temperature): Configuration of temperature output signal:
0 = Temperature value
1 = Recorded minimum temperature value
2 = Recorded maximum temperature value
0…2 0
OP 04 AO2 (temperature): Minimum limitation of temperature output
signal 3) 4)
0 … 100 % 0 %
OP 05 AO2 (temperature): Maximum limitation of temperature output
signal 3) 4
0 … 100 % 100 %
3) The Output signal will be scaled according to selected input range, selected limitation of output signal and the output
signal range selected by the jumper.
4) If the default values are changed, the position of JP2 has no influence and the output signal range defined with the
parameters applies.
IP = Input Parameter
OP = Output Parameter
CI
= CO2 Input
TI = Temperature Input
AO = Analog Output