YOKOGAWA UT32A-C Operation Manual Download

Page: 1 / 10

IM 05P01F31-11EN page 1/10

Contents

1. Safety Precautions

2. Model and Suffix Codes

3. How to Install

4. Hardware Specifications

5. How to Connect Wires

6. Terminal Wiring Diagrams

Introduction

Thank you for purchasing the UT32A Digital Indicating Controller (Entry model).

This operation guide describes the basic operations of the UT32A. The guide should

be provided to the end user of this product.

Be sure to read this operation guide before using the product in order to ensure

correct operation.

For details of each function, refer to the electronic manual. Before using the product,

refer to the table of Model and Suffix Codes to make sure that the delivered product

is consistent with the model and suffix codes you ordered. Also make sure that the

following items are included in the package.

• Digital Indicating Controller (the model you ordered)

..............................

• Set of Brackets ........................................................................................

• Unit Label (L4502VZ)

..............................................................................

• Tag Label (L4502VE)

..............................................................................

(Only when ordered.)

• Operation Guide (this document)

............................................................

x5 (A3 size)

(Installation and Wiring, Initial Settings, Operations, and Parameters)

Target Readers

This guide is intended for the following personnel;

• Engineers responsible for installation, wiring, and maintenance of the equipment.

• Personnel responsible for normal daily operation of the equipment.

1. Safety Precautions

The following symbol is used on the instrument. It indicates the possibility of injury

to the user or damage to the instrument, and signifies that the user must refer to the

operation guide or user’s manual for special instructions. The same symbol is used in

the operation guide and user’s manual on pages that the user needs to refer to, together

with the term “WARNING” or “CAUTION.”

WARNING

Calls attention to actions or conditions that could cause serious

or fatal injury to the user, and indicates precautions that should be

taken to prevent such occurrences.

CAUTION

Calls attention to actions or conditions that could cause injury to

the user or damage to the instrument or property and indicates pre-

cautions that should be taken to prevent such occurrences.

AC/DC

The equipment wholly protected by double insulation or reinforced insulation.

Functional grounding terminals

(Do not use this terminal as a protective grounding terminal).

Note

Identifies important information required to operate the instrument.

■

Warning and Disclaimer

(1) YOKOGAWA makes no warranties regarding the product except those stated in

the WARRANTY that is provided separately.

(2) The product is provided on an "as is" basis. YOKOGAWA assumes no liability to

any person or entity for any loss or damage, direct or indirect, arising from the

use of the product or from any unpredictable defect of the product.

■ Safety, Protection, and Modification of the Product

(1) In order to protect the system controlled by this product and the product itself,

and to ensure safe operation, observe the safety precautions described in the

operation guide. Use of the instrument in a manner not prescribed herein may

compromise the product's functions and the protection features inherent in the

device. We assume no liability for safety, or responsibility for the product's quality,

performance or functionality should users fail to observe these instructions when

operating the product.

(2) Installation of protection and/or safety circuits with respect to a lightning

protector; protective equipment for the system controlled by the product and the

product itself; foolproof or fail-safe design of a process or line using the system

controlled by the product or the product itself; and/or the design and installation

of other protective and safety circuits are to be appropriately implemented as the

customer deems necessary.

(3) Be sure to use the spare parts approved by YOKOGAWA when replacing parts

or consumables.

(4) This product is not designed or manufactured to be used in critical applications

that directly affect or threaten human lives. Such applications include nuclear

power equipment, devices using radioactivity, railway facilities, aviation

equipment, air navigation facilities, aviation facilities, and medical equipment.

If so used, it is the user’s responsibility to include in the system additional

equipment and devices that ensure personnel safety.

(5) Modification of the product is strictly prohibited.

(6) This product is intended to be handled by skilled/trained personnel for electric devices.

(7) This product is UL Recognized Component. In order to comply with UL standards,

end-products are necessary to be designed by those who have knowledge of the

requirements.

WARNING

Power Supply

Ensure that the instrument’s supply voltage matches the voltage

of the power supply before turning ON the power.

Do Not Use in an Explosive Atmosphere

Do not operate the instrument in locations with combustible

or explosive gases or steam. Operation in such environments

constitutes an extreme safety hazard. Use of the instrument in

environments with high concentrations of corrosive gas (H

, etc.) for extended periods of time may cause a failure.

Do Not Remove Internal Unit

The internal unit should not be removed by anyone other than

YOKOGAWA's service personnel. There are dangerous high voltage

parts inside. Additionally, do not replace the fuse by yourself.

Damage to the Protective Construction

Operation of the instrument in a manner not specified in the

operation guide may damage its protective construction.

CAUTION

This instrument is an EMC class A product. In a domestic environ-

ment this product may cause radio interference in which case the

user needs to take adequate measures.

2. Model and Suffix Codes

■

UT32A «Entry Model»

Model

Suffix code

Option

code

Description

UT32A

Digital Indicating Controller (Power supply: 100-240 V

AC) (provided with 2 DOs)

Type 1:

Basic

control

-V

Voltage pulse output type

-C

Current output type

-R

Relay output type

Type 2:

Functions

None

RS-485 communication (Max. 38.4 kbps, 2-wire/4-wire) (*1)

Type 3: Fixed code

None

Display language (*2)

-1

English (Default. Can be switched to other language by the setting.)

-2

German (Default. Can be switched to other language by the setting.)

-3

French (Default. Can be switched to other language by the setting.)

-4

Spanish (Default. Can be switched to other language by the setting.)

Case color

White (Light gray)

Black (Light charcoal gray)

Fixed code

-00

Always "-00" (for Standard Code Model)

Option codes

/LP

24 V DC loop power supply

/DC

Power supply 24 V AC/DC

/CT

Coating (*3)

/CV

Terminal cover

*1: When the /LP option is specified, the RS-485 communication of the Type 2 code “1” is 2-wire

system.

*2: English, German, French, and Spanish are available for the guide display.

*3: When the /CT option is specified, the UT32A does not conform to the safety standards (UL

and CSA) and CE marking (Products with /CT option are not intended for EEA-market).

■ Customized Product

For customized product, the product is identified by the option code of /S# (where ‘#’

is a number).

Contact your supplier in case your instrument has option /S#, and you are not

in the possession of FX1-[Model code]-S# or IM [Model code]-S# (where [Model

code] means, for example, UT55A).

■

Accessories (sold separately)

The following is an accessory sold separately.

• LL50A Parameter Setting Software

Model

Suffix code

Description

LL50A

-00

Parameter Setting Software

• External Precision Resistor

Model

Suffix code

Description

X010

See the General Specifications (*) Resistance Module

*: Necessary to input the current signal to the voltage input terminal.

• Terminal Cover: Model UTAP002

• Manuals

Note: Manuals can be downloaded from a website. URL: http://www.yokogawa.com/ns/ut/im/

• Brackets

Part number: L4502TP (2 pcs for upper and lower sides)

3. How to Install

■

Installation Location

The instrument should be installed in indoor locations meeting the following

conditions:

• Instrumented panel

This instrument is designed to be mounted in an instrumented panel. Mount the

instrument in a location where its terminals will not inadvertently be touched.

• Well ventilated locations

Mount the instrument in well ventilated locations to prevent the instrument’s inter-

nal temperature from rising.

However, make sure that the terminal portions are not exposed to wind. Exposure

to wind may cause the temperature sensor accuracy to deteriorate. To mount mul

tiple indicating controllers, see the external dimensions/panel cutout dimensions

which follow.

If mounting other instruments adjacent to the instrument, comply with

these panel cutout dimensions to provide sufficient clearance between the instruments.

• Locations with little mechanical vibration

Install the instrument in a location subject to little mechanical vibration.

• Horizontal location

Mount the instrument horizontally and ensure that it is level, with no inclination to

the right or left.

Front panel

of controller

Keep this angle

within 30°

Rear of

controller

30°

Note

If the instrument is moved from a location with low temperature and low humidity

to a place with high temperature and high humidity, or if the temperature changes

rapidly, condensation will result. Moreover, in the case of thermocouple inputs,

measurement errors will result. To avoid such a situation, leave the instrument in the

new environment under ambient conditions for more than 1 hour prior to using it.

Do not mount the instrument in the following locations:

• Outdoors

• Locations subject to direct sunlight or close to a heater

Install the instrument in a location with stable temperatures that remain close to an

average temperature of 23°C. Do not mount it in locations subject to direct sunlight

or close to a heater. Doing so adversely affects the instrument.

• Locations with substantial amounts of oily fumes, steam, moisture, dust, or

corrosive gases

The presence of oily fumes, steam, moisture, dust, or corrosive gases adversely

affects the instrument. Do not mount the instrument in locations subject to any of

these substances.

• Areas near electromagnetic field generating sources

Do not place magnets or tools that generate magnetism near the instrument. If the

instrument is used in locations close to a strong electromagnetic field generating

source, the magnetic field may cause measurement errors.

• Locations where the display is difficult to see

The instrument uses an LCD for the display unit, and this can be difficult to see

from extremely oblique angles. Mount the instrument in a location where it can be

seen as much as possible from the front.

• Areas close to flammable articles

Absolutely do not place the instrument directly on flam-

mable surfaces. If such a circumstance is unavoidable

and the instrument must be placed close to a flammable

item, provide a shield for it made of 1.43 mm thick plated

steel or 1.6 mm thick unplated steel with a space of at

least 150 mm between it and the instrument on the top,

bottom, and sides.

• Areas subject to being splashed with water

WARNING

Be sure to turn OFF the power supply to the controller before in-

stalling it on the panel to avoid an electric shock.

150 mm

Operation

Guide

IM 05P01F31-11EN

UT32A-V , -C, -R

Digital Indicating Controller

Operation Guide

This operation guide describes installation, wiring, and other tasks required to make the

controller ready for operation.

3rd Edition : Mar. 2018

Installation and Wiring

For details of the each function, refer to the electronic manual. Manuals can be

downloaded or viewed at the following URL.

Functional

Enhancement

http://www.yokogawa.com/ns/ut/im/

«Entry Model»

www.yokogawa.com/ns

YOKOGAWA ELECTRIC CORPORATION

Network Solutions Business Division

2-9-32, Naka-cho Musashino-shi, Tokyo 180-8750 JAPAN

YOKOGAWA CORPORATION OF AMERICA

Head office and for product sales

2 Dart Road, Newnan, Georgia 30265, USA

YOKOGAWA EUROPE B.V.

Headquarters

Euroweg 2, 3825 HD Amersfoort, THE NETHERLANDS

• Authorised Representative in the EEA

Yokogawa Europe BV. (Address: Euroweg 2 , 3825 HD Amersfoort, The Nether-

lands) is the Authorised Representative of Yokogawa Electric Corporation for this

Product in the EEA.

• Printed Manuals

Model

Description

UT35A, UT32A Digital Indicating Controller (Panel Mounting Type) Operation Guide

Standard Code Model

IM 05P01D31-11EN

UT35A, UT32A Digital Indicating Controller (Panel Mounting Type) Operation Guide

Detailed Code Model

IM 05P01D31-15EN

UT35A/MDL, UT32A/MDL Digital Indicating Controller (DIN Rail Mounting Type)

Operation Guide

Standard Code Model

IM 05P01D81-11EN

UT32A-D Digital Indicating Controller (Dual-loop, Panel Mounting Type)

Operation Guide

Standard Code Model

IM 05P08D31-11EN

UT32A-D/MDL Digital Indicating Controller (Dual-loop, DIN Rail Mounting Type)

Operation Guide

Standard Code Model

IM 05P08D81-11EN

UT35A/RSP, UT32A/RSP Digital Indicating Controller (Non-isolated Remote

Input, Panel Mounting Type) Operation Guide

Standard Code Model

IM 05P01D31-81EN

UT32A Digital Indicating Controller Operation Guide

Entry Model

IM 05P01F31-11EN

Precautions on the Use of the UTAdvanced Series

IM 05P01A01-11EN

• Electronic Manuals

You can download the latest manuals from the following website:

URL: http://www.yokogawa.com/ns/ut/im/

Model

Description

UT35A, UT32A Digital Indicating Controller (Panel Mounting Type) Operation Guide

Standard Code Model

IM 05P01D31-11EN

UT35A, UT32A Digital Indicating Controller (Panel Mounting Type) Operation Guide

Detailed Code Model

IM 05P01D31-15EN

UT35A/MDL, UT32A/MDL Digital Indicating Controller (DIN Rail Mounting Type)

Operation Guide

Standard Code Model

IM 05P01D81-11EN

UT35A/UT32A Digital Indicating Controller User’s Manual

IM 05P01D31-01EN

UT32A-D Digital Indicating Controller (Dual-loop, Panel Mounting Type)

Operation Guide

Standard Code Model

IM 05P08D31-11EN

UT32A-D/MDL Digital Indicating Controller (Dual-loop, DIN Rail Mounting Type)

Operation Guide

Standard Code Model

IM 05P08D81-11EN

UT32A-D, UT32A-D/MDL Digital Indicating Controller User’s Manual

IM 05P08D31-01EN

UT35A/RSP, UT32A/RSP Digital Indicating Controller (Non-isolated Remote

Input, Panel Mounting Type) Operation Guide

Standard Code Model

IM 05P01D31-81EN

UT32A Digital Indicating Controller Operation Guide

Entry Model

IM 05P01F31-11EN

UT32A Digital Indicating Controller User’s Manual

Entry Model

IM 05P01F31-01EN

UTAdvanced Series Communication Interface (RS-485, Ethernet) User’s Manual IM 05P07A01-01EN
UTAdvanced Series Communication Interface (Open Network) User’s Manual

IM 05P07A01-02EN

LL50A Parameter Setting Software Installation Manual

IM 05P05A01-01EN

LL50A Parameter Setting Software User’s Manual

IM 05P05A01-02EN

Precautions on the Use of the UTAdvanced Series

IM 05P01A01-11EN

• General Specification

Model

Description

UT35A, UT32A Digital Indicating Controller (Panel Mounting Type)

GS 05P01D31-01EN

UT35A/MDL, UT32A/MDL Digital Indicating Controller (DIN Rail Mounting Type) GS 05P01D81-01EN
UT32A-D Digital Indicating Controller (Dual-loop, Panel Mounting Type)

GS 05P08D31-01EN

UT32A-D/MDL Digital Indicating Controller (Dual-loop, DIN Rail Mounting Type) GS 05P08D81-01EN
LL50A Parameter Setting Software

GS 05P05A01-01EN

The last two characters of the manual number and general specification number indicate the

language in which the manual is written.

■

Protection of Environment

Waste Electrical and Electronic Equipment (WEEE), Directive

This is an explanation of how to dispose of this product based on Waste Electrical

and Electronic Equipment (WEEE), Directive. This directive is only valid in the EU.

● Marking

This product complies with the WEEE Directive marking