background image

CAUTION:   

Be sure to turn off the power switch before connecting or disconnecting the soldering iron. 

Failure to do so may damage the soldering station.

 

1.Connect the connector plug of the iron handle cord to the socket in front of the soldering station. 

Take notice of the inserting position of connector plug. 

2. Place the soldering iron in the iron holder. 

3. Insert the power plug into the grounding power socket. 

4. Connect one end of grounding cord to the grounding hole of the soldering station and the other 

to ground. 

5. Switch on the power supply. 

 

3.3 

Setting the parameters

 

3.3.1 Setting the password 

The initial password is 000 and the temperature can be set after turning on the power supply at this 

state. If administrator wants to limit the authority and he can change the password and then those 

being authorized can set the parameters. 

1.

 

Enter the password setting: 

Turn off the power supply. press and hold

 “

” 

and 

“▽”

keys simultaneously and then press 

the power switch until the display shows 

.It means in the password setting state. 

2.

 

Enter the initial password: 

Press 

“*” 

key after the display shows 

, and then the display shows 

. In 

the 

  state,  input  the  initial  password  by  pressing 

  and 

“▽”

keys.  And 

press

“*”

 key after inputting the right password. 

      a) If the inputted password is error: 

     

The  soldering  station  will  jump  over  the  password  setting  process  into  the  normal  working 

process after the display shows the setting password about four seconds. But the temperature 

cannot be changed in normal working process because of inputting the error password. 

b) If the inputted password is correct: 

If the display shows 

, this means the inputting password is correct. After displaying 

about  four  seconds,  the  station will  come  into  the normal  work  process,  and  it  can  set  the 

temperature. 

3.    Input the new password: 

Note: the next inputted password must be same with the last inputted password, and then the 

new  password  will  be  recorded  in  the  soldering  station  and  change  the  password 

successfully. (Operation as follows) 

1)

 

Input the new password:

 when inputting the correct initial password, the display shows 

and  then  press 

“*”

  and 

  keys  simultaneously  in  about  four  seconds  then 

showing 

.  It  is  in  the  new  password  setting  process.  Press 

“*”

  key  and  the 

display shows 

. After that, press

 “

” 

or 

“▽”

key to input the new password. 

       

2) Repeat the  new password: 

after inputting the new password and then press 

“*” 

key to 

. Now it must input the new password again. Press 

“*”

 key and the display shows 

. After that, press

 “

” 

or

“▽”

key to input the new password. 

3) If the next inputted password is same with the last inputted password: 

press “*” key 

and  then  the  new  password  will  be  recorded  in  the  soldering  station  and  change  the 

password successfully. 

4) If the next inputted password is not same with the last time:

 

Press  “*”  key  to 

  and  then  input  the  new  password  again  until  the  lately 

two passwords are identical.

 

 

3.3.2 Setting the temperature 

Note:  *  Make  sure  the  temperature  of  the  station  can  be  adjusted  (inputted  password  is 

correct or the password is initial 000). 

* Do not turn off the power supply when setting the temperature, or  else the setting 

value will not be memorized.

 

1. The process of temperature setting 

1)

 

If the password is 000 and can jump into the temperature setting process when turning on 

the power supply. 

2)

 

If the password has been changed, it must input the correct password firstly and then   

2 If the value of „c‟ is over the below value, remove lightly the oxidation in the joint part of the 

tip and the heat element with sandpaper or steel wool. 

Page5 

 

Summary of Contents for SD-101













Reviews: