manualshive.com logo in svg

Vecow ECX-3000 PEG, User Manual, Page: 33 / 159

Share
Download
Vecow ECX-3000 PEG User Manual Download Page 33

25

©Vecow ECX-3000 PEG User Manual  

GETTING TO KNOW YOUR ECX-3000 PEG

2.2  Front Panel I/O Functions

In Vecow ECX-3000 PEG series family, all I/O connectors are located on front 

panel and rear panel. Most of the general connections to computer device, such 

as USB, LAN Jack, USB TYPE-C, HDMI, DVI-I, Display Port and any additional 

storage, are placed on the front panel.

2.2.1   Reset Tact Switch

It is a hardware reset switch. Use this switch to reset the system without power off 

the system. Press the Reset Switch for a few seconds, then reset will be enabled.

It is a hardware reset switch. Use this switch to reset the system without power off 

the system. Press the Reset Switch for a few seconds, then reset will be enabled.

DP

DP

HDMI

DVI-I

LAN 2

LAN 1

WLAN

RST

SIM 3

SIM 2

SIM 1

RTC

TypeC

20

DP

DP

HDMI

DVI-I

LAN 2

LAN 1

WLAN

RST

SIM 3

SIM 2

SIM 1

RTC

TypeC

20

Summary of Contents for ECX-3000 PEG
































































































































































Reviews:

No comments